Okuma OSP-P300S/P300L CNC Alarm B List – Comprehensive Guide

Okuma OSP-P300S/P300L Alarm-B list.
For cnc machinists who work on cnc machines with Okuma cnc controls.

Classification Of Okuma Alarms

Alarms related with the OSP are classified into five types, which are

• Alarm P
• Alarm A
• Alarm B (listed below)
• Alarm C
• Alarm D
• ERROR

Below are  listed Okuma B type alarms for Okuma OSP-P300S/P300L CNC systems.

Okuma Alarm B List

• 2049 PLC axis stroke end over
• 2050 PLC axis command
• 2051 PLC axis continuous positioning over
• 2052 Blue screen
• 2053 P100-Menu error
• 2058 Error occurred while CAS work
• 2059 Non-functioning device detected
• 2060 Fan motor error on panel computer unit
• 2090 The remaining time after relocation has passed
• 2092 MCS Parameter learning error
• 2114 MCS Inertia identification error
• 2120 Overload detected.
• 2132 VDU communication error
• 2133 VDU detected error
• 2134 VDU initialization failure
• 2135 MCS DD encoder link error
• 2136 MCS DD Encoder error
• 2137 MCS DD Encoder (slave sensor) error
• 2138 MCS DD encoder initialization failure
• 2139 MCS DD encoder (slave sensor) initialization failure
• 2144 MCS Power supply unit overload
• 2150 MCS Undefined alarm number
• 2151 MCS Inverter unit fault
• 2152 Mistake in data from MCS to NC
• 2153 MCS CON APA deviation
• 2154 MCS Power supply unit error
• 2155 MCS Converter link error
• 2156 MCS DC-bus voltage alarm
• 2157 MCS Motor overcurrent
• 2158 MCS Power unit overheat
• 2159 MCS Power unit overload
• 2160 MCS Supply voltage flutter
• 2161 MCS Inverter capacity differs from spec.
• 2162 MCS Winding change failure
• 2163 MCS Encoder link error
• 2164 MCS Encoder detected error
• 2165 MCS Encoder initialization failure
• 2166 MCS Encoder with shaft detected error
• 2167 MCS Encoder with shaft initialization failure
• 2168 MCS ABSO SCALE error
• 2169 MCS ABSO SCALE initialization failure
• 2170 MCS Magnetic encoder alarm
• 2171 MCS Resolver alarm
• 2172 MCS Pulse generator count over
• 2173 MCS Motor overheat
• 2174 MCS Servo link error
• 2175 MCS Servo link disconnection
• 2176 Mistake in data from NC to MCS
• 2177 MCS Servo data error
• 2178 MCS Illegal command
• 2179 MCS CON speed over
• 2180 MCS Speed command over
• 2181 MCS DIFF over
• 2182 MCS APA speed over
• 2183 MCS Full-closed APA error
• 2184 MCS Over speed
• 2185 MCS Speed deviation over
• 2186 MCS Collision detected
• 2187 MCS Urgent-stop time over
• 2188 MCS Belt is broken
• 2189 MCS Axis change control error
• 2190 MCS Independent encoder initialization failure
• 2191 MCS Calculated current position lies outside range
• 2192 MCS Motor overload
• 2194 MCS ABSO SCALE sub-slider error
• 2195 MCS Tandem control communication error
• 2196 MCS Full abso scale link error
• 2197 MCS Full abso scale error
• 2198 MCS Full abso scale initialization failure
• 2199 MCS Axis stop signal error
• 2200 G-code error
• 2201 M-code error
• 2202 Common variable error
• 2203 System variable error
• 2204 Sequence name error
• 2205 Numeric data error
• 2206 Character use error
• 2207 Program name error
• 2208 Character string error
• 2209 Hexadecimal data error
• 2210 Spindle max revolution error
• 2212 G132/G133 command error
• 2213 Program factor over
• 2214 Subscript left side incorrect
• 2215 Local variable use over
• 2216 System variable setting data over
• 2217 Output variable setting data mistake
• 2218 UNUSABLE G-code
• 2219 UNUSABLE M-code
• 2220 Subscript left side illegal
• 2221 UNUSABLE output variable No
• 2222 UNUSABLE input variable No
• 2223 UNUSABLE turret direct code
• 2224 UNUSABLE contour generation command
• 2225 UNUSABLE Y-Z circle command
• 2226 UNUSABLE thread cutting command
• 2227 Mnemonic or local variable mistake
• 2228 VSET sequence left command mistake
• 2229 EXPRESSION right side
• 2230 EXPRESSION calculation error
• 2231 EXPRESSION syntax incorrect
• 2232 EXPRESSION subscript mistake
• 2233 EXPRESSION buffer over
• 2234 EXPRESSION local variable
• 2235 Equal does not exist
• 2236 Program end code not found
• 2237 BRANCH (IF,GOTO) sequence name
• 2238 BRANCH(IF,GOTO) condition
• 2239 Mistake in F command
• 2240 Mistake in F/E command
• 2241 Mistake in I command
• 2242 Mistake in J command
• 2243 Mistake in K command
• 2244 Mistake in L command
• 2245 Mistake in P command
• 2246 Mistake in S command
• 2247 No S command
• 2248 Mistake in T command
• 2249 Mistake in X command
• 2250 Mistake in X/Z command
• 2251 Mistake in Z command
• 2252 Mistake in arc command
• 2253 Mistake in angle command
• 2254 Mistake in thread cutting cycle command
• 2255 Mistake in arc radius command
• 2256 Mistake in D command
• 2257 Mistake in gauging cycle command
• 2258 Mistake in C command
• 2259 Mistake in SB command
• 2260 Mistake in QA command
• 2261 Mistake in X/Y command
• 2262 Mistake in incremental command
• 2263 Command required for X-, Y-axes
• 2264 Mistake in Y command
• 2265 Distance calculation over limit
• 2266 Mistake in R command
• 2267 Mistake in drilling cycle command
• 2268 Mistake in angle command
• 2269 Angle chamfering command error
• 2270 Mistake in CD command
• 2271 Mistake in CL command
• 2272 Mistake in TM command
• 2273 Mistake in W command
• 2274 Mistake in CB command
• 2275 Mistake in HP command
• 2276 Mistake in CC command
• 2277 Mistake in torque limit command
• 2278 SUB PROGRAM repetition
• 2279 SUB PROGRAM stack
• 2280 SUB PROGRAM program name
• 2281 SUB PROGRAM data print
• 2282 SCHEDULE PROGRAM ‘Q’
• 2283 SCHEDULE PROGRAM mnemonic code
• 2284 SCHEDULE PROGRAM program end
• 2285 SCHEDULE PROGRAM main program load
• 2286 Plus variable limit over
• 2287 Minus variable limit over
• 2288 User reserve code
• 2289 Unable to write backup data file
• 2290 Program name not selected
• 2291 Main sequence error
• 2292 Restart failure
• 2293 MDI special G-code
• 2294 Special G-code table
• 2295 STM time over
• 2296 UGC No program end code
• 2297 UGC DELETE syntax
• 2298 UGC DEF syntax
• 2299 UGC TIP syntax
• 2300 UGC TIF syntax
• 2301 UGC No shape entry
• 2302 UGC Illegal numerical data
• 2303 UGC Illegal character
• 2304 UGC User variable
• 2305 UGC System variable
• 2306 UGC Illegal command
• 2307 UGC Program factor over
• 2308 UGC Coordinate data
• 2309 UGC END syntax
• 2310 UGC Command over
• 2311 UGC Command format
• 2312 UGC Additional parameter
• 2313 UGC Expression
• 2314 UGC Figure entry area over
• 2315 UGC Unable to delete
• 2316 READ/WRITE No spec
• 2317 READ/WRITE Buffer over
• 2318 READ/WRITE Device No.
• 2319 READ/WRITE Data
• 2320 READ communication error
• 2321 WRITE communication error
• 2322 GET/PUT No spec.
• 2323 GET/PUT Buffer over
• 2324 GET/PUT Number of digits
• 2325 GET/PUT Variable designation
• 2326 GET Numerical data
• 2327 Calculation function no spec.
• 2328 Sub-program no spec.
• 2329 Sub-spindle interference distance
• 2330 Input/output variable no spec.
• 2331 Multiple machining no spec.
• 2332 Sub-spindle no spec.
• 2334 In-process gauging no spec.
• 2335 Post-process gauging no spec.
• 2336 Animation no spec.
• 2337 Graphic backup data file write failure
• 2338 Spindle orientation no spec.
• 2339 Load monitor no spec.
• 2340 Thread phase matching no spec.
• 2341 Circular thread cutting no spec.
• 2342 Circular thread cutting command
• 2343 Tool retract no spec.
• 2344 Tool retract interrupt enable com.
• 2345 Tool retract interrupt disable com.
• 2346 Tool retract interrupt return com.
• 2347 ROBOT no spec.
• 2348 ROBOT program name
• 2349 LOADER no spec.
• 2350 LOADER program name
• 2351 Coupling device program select no spec.
• 2353 CHAMFERING G01 mode
• 2354 CHAMFERING L over
• 2355 CHAMFERING L illegal order
• 2356 CHAMFERING X, Z illegal order
• 2357 CHAMFERING Any angle calculation
• 2358 CHAMFERING Any angle
• 2359 NOSE-R COMP. No spec.
• 2360 NOSE-R COMP. NOSE-R > circle-R
• 2361 NOSE-R COMP. Calculation
• 2362 NOSE-R COMP. Cancel G00 G01
• 2363 NOSE-R COMP. No cross point
• 2364 NOSE-R COMP. Entrance command error
• 2365 NOSE-R COMP. Thread cutting cycle
• 2366 TOOL RADIUS COMP. No spec.
• 2367 TOOL RADIUS COMP. NOSE-R comp. surface change
• 2368 TOOL RADIUS COMP. C-axis separation
• 2369 TOOL RADIUS COMP. QA command
• 2370 TOW-ALONG TAILSTOCK MOVEMENT no spec.
• 2371 TOW-ALONG TAILSTOCK MOVEMENT condition
• 2372 LASER MEASUREMENT no spec.
• 2373 LASER MEASUREMENT condition
• 2374 LAP No spec.
• 2375 LAP B illegal order
• 2376 LAP D illegal order
• 2377 LAP DA(DB) illegal order
• 2378 LAP H illegal order
• 2379 LAP H-U(W) < D (M73)
• 2380 LAP U(W) illegal order
• 2381 LAP U(W) > H
• 2382 LAP XA(ZA), XB(ZB) illegal order
• 2383 LAP Calculation error
• 2384 LAP Down step number over
• 2385 LAP Entry in LAP
• 2386 LAP Sequence name
• 2387 Unable to LAP Control
• 2388 LAP No G-code
• 2389 LAP NOSE-R comp. cancel
• 2390 LAP Entry in NOSE-R comp.
• 2391 LAP Shape designation
• 2392 MULTI CYCLE B illegal order
• 2393 MULTI CYCLE D illegal order
• 2394 MULTI CYCLE F illegal order
• 2395 MULTI CYCLE H illegal order
• 2396 MULTI CYCLE H-U(W) < D (M73)
• 2397 MULTI CYCLE I,K over
• 2398 MULTI CYCLE I,K illegal order
• 2399 MULTI CYCLE L illegal order
• 2400 MULTI CYCLE Entry in LAP
• 2401 MULTI CYCLE U(W) illegal order
• 2402 MULTI CYCLE U(W) > H
• 2403 MULTI CYCLE X,Z illegal order
• 2404 MULTI CYCLE Angle
• 2405 MULTI CYCLE Tool offset
• 2406 MULTI CYCLE Cycle start point
• 2407 MULTI CYCLE Entry in NOSE-R comp.
• 2408 MULTI CYCLE Width
• 2409 TOOL LIFE CONTROL no spec.
• 2410 Tool life management No spare tool
• 2411 TOOL LIFE CONTROL tool group
• 2412 TOOL LIFE CONTROL no T-entry
• 2413 TOOL LIFE CONTROL tool offset group
• 2414 TOOL LIFE CONTROL no T-offset
• 2415 MULTI-MACHINING CYCLE No spec.
• 2416 MULTI-MACHINING CYCLE C
• 2417 MULTI-MACHINING CYCLE I,K
• 2418 MULTI-MACHINING CYCLE Q
• 2419 MULTI-MACHINING CYCLE F
• 2420 MULTI-MACHINING CYCLE L
• 2421 MULTI-MACHINING CYCLE D
• 2422 MULTI-MACHINING CYCLE X,Z
• 2423 MULTI-MACHINING CYCLE SA
• 2424 MULTI-MACHINING CYCLE Feed G94
• 2425 MULTI-MACHINING CYCLE A
• 2426 MULTI-MACHINING CYCLE Thread cycle
• 2427 MULTI-MACHINING CYCLE U,W
• 2428 MULTI-MACHINING CYCLE SB
• 2429 MULTI-MACHINING CYCLE Y-axis mode
• 2430 ATC no spec.
• 2431 ATC syntax
• 2432 ATC TC
• 2434 ATC TL
• 2435 ATC MT
• 2436 ATC MG
• 2438 Unable to M06/M228 command
• 2440 Y-axis no spec.
• 2441 2 saddle machine no spec.
• 2444 Carrier axis variable limit over
• 2445 3-D coordinate conversion
• 2452 Chuck barrier area
• 2453 Tailstock barrier area
• 2456 W-axis minus variable limit over
• 2457 X-axis correction stroke end over
• 2459 Restart axis position is illegal
• 2460 Change timing G13/G14
• 2462 Change timing G122/G123
• 2463 Change timing G140/G141/G142
• 2464 Spindle/turret G-code
• 2465 G122/G123 command mismatch
• 2466 Unable to issue M100 command during Nose-R comp.
• 2472 Y-axis control mode
• 2475 W-axis command G-code
• 2476 Mirror image coordinate selection
• 2477 Sub-spindle mode
• 2478 No workpiece coordinate mode command
• 2479 Contour generation calculation error
• 2480 G132/G133 command error
• 2486 NC turret no spec.
• 2487 Unable to select coordinates
• 2488 UNUSABLE X-axis command
• 2489 NC tailstock parameter error
• 2490 Chuck pressure out of range
• 2491 Horizon barrier intrusion
• 2492 Interrupt program: illegal command
• 2493 Linked external equipment program selection
• 2494 Chuck pressure command illegal
• 2495 Inverse time feed command format
• 2496 CAM data cannot be transmitted.
• 2497 T code
• 2498 Learning cannot be executed.
• 2499 Spindle marker latch data error
• 2500 MULTI-MACHINING CYCLE HS,HI,HJ,HK
• 2501 Recovering synchronous error
• 2502 Block Delete command error
• 2503 End sequence name error
• 2504 PREMIUM THREAD Command error
• 2505 CAM machine no spec.
• 2506 Tool center point control not possible
• 2507 CHP command error
• 2508 Machining mode command format
• 2509 MULTI-MACHINING CYCLE Return point
• 2510 Mistake in torque skip cycle command
• 2511 Remote buffer operation
• 2512 M-tool spindle overload
• 2513 Coordinate calculation
• 2514 MULTI CYCLE C-axis shift
• 2515 Remote buffer operation time out
• 2516 Remote buffer operation communication error
• 2517 W-axis control mode
• 2518 Synchronized tapping command
• 2519 Tailstock control command
• 2520 Mistake in TP command
• 2521 Mistake in BT command
• 2522 Mistake in BA command
• 2523 Thermistor error
• 2524 Mistake in AT command
• 2525 Chuck coordinate change condition
• 2528 Program selection unsuitable
• 2529 Thermal deviation compensation
• 2530 Machining process instruction no.
• 2531 Mirror turning mode
• 2532 System variable set condition error
• 2533 Steady rest over interference pos.
• 2534 LBB turret rotation impossible
• 2536 Coordinate movement rotation copy
• 2537 SLANT PROCESS MODE
• 2538 Incorrect system variable
• 2539 Mistake in B command
• 2541 PROGRAM PRINT command
• 2542 Feed axis retract function command
• 2543 Turret index error position
• 2544 TOOL-ID TOOL DATA
• 2545 MULTI-MACHINING CYCLE LD
• 2546 MULTI-MACHINING CYCLE LK
• 2547 No decimal point
• 2548 X-, Z-axis synchronized feed mode
• 2549 Tool no. mismatch after ATC sequence restart
• 2550 Home position no spec.
• 2551 External home position command
• 2552 Barrier area
• 2555 Linear guide cover interference area command
• 2557 Illegal steady rest command
• 2558 Turning position selection
• 2559 Attachment rotation not possible
• 2561 Illegal system command variable
• 2562 Tool posture fluctuation reduction
• 2563 Mistake in TE command
• 2564 Index disable position
• 2565 Load monitor system variable
• 2566 MULTI-MACHINING CYCLE No M-tool cycle command
• 2567 No helical cutting specifications
• 2568 Mistake in OF command
• 2569 Thermal deviation comp. backup failure
• 2570 W-axis position condition
• 2571 W-axis position no spec.
• 2572 Mistake in RC command
• 2573 Taper cutting cycle
• 2575 Mistake in ‘TD’,’TDG’,’OS’ commands
• 2576 Mistake in H command
• 2577 No axis movement command
• 2578 NO D COMMAND
• 2579 NO L COMMAND
• 2580 Mistake in XS command
• 2581 CAM data deployment mode
• 2582 CAM data file write protect
• 2583 Compensation value overflow
• 2584 CON speed XS-axis
• 2585 XS-axis command turret mode
• 2586 Synchronous mode execution impossible
• 2587 No A command
• 2588 Mistake in OF command
• 2589 Definition conditions
• 2590 Y-axis command
• 2591 Mistake in point command
• 2592 Transport barrier entry command
• 2593 Mistake in CF command
• 2594 Mistake in RJ command
• 2595 Synchronized rotation speed over
• 2596 Synchronized tap overload
• 2597 G15 command
• 2598 No Spec code. “Tool information management spec”
• 2599 Command not possible while mounting LBB.
• 2600 LAW-V machine no spec.
• 2601 Unable to issue T/TE command simultaneously
• 2602 SCHEDULE PROGRAM main program load
• 2603 Spindle rotation fluctuation control no spec.
• 2604 Tow-along steady rest no spec.
• 2605 Tow-along tailstock no spec.
• 2606 READ/WRITE file open
• 2607 Mistake in AP command
• 2608 Mistake in ON command
• 2609 A-axis control no spec.
• 2610 Zero offset select inpossible
• 2611 Spindle fluctuation control no spec.
• 2612 Mistake in TR command
• 2613 Mistake in MTM command
• 2614 Mistake in MTS command
• 2615 Mistake in MGS command
• 2616 B-axis mode
• 2617 Zero setting condition
• 2618 Workpiece detection sensor not ready
• 2619 Mistake in SW command
• 2622 Unset system variable read
• 2623 B-axis no spec.
• 2624 Tow-along steady rest type-B no spec
• 2625 Tow-along steady rest movement condition
• 2626 W-axis overlap
• 2628 Mistake in TW command
• 2629 Mistake in FW command
• 2630 Mistake in SC command
• 2631 DNC-DT Path name
• 2632 DNC-DT Program select
• 2633 DNC-DT Preload error
• 2634 DNC-DT Delete error
• 2635 Y-axis mode
• 2637 No axis movement command
• 2638 A/B saddle synchronized motion command
• 2639 Unable to issue C-axis command during helical cutting
• 2640 AC thread rotation count error
• 2641 AC thread fluctuation control not possible
• 2642 READ/WRITE No empty SAT
• 2643 READ/WRITE File open
• 2644 Unusable PRINT request
• 2645 YS-axis position
• 2646 SYSTEM VARIABLE C-axis separation
• 2648 MG tool ready cycle no spec.
• 2649 SYSTEM VARIABLE Y-axis mode
• 2650 SYSTEM VARIABLE B-axis mode
• 2651 C-axis multi rotation mode
• 2652 Mistake in HA command
• 2653 Mistake in MN command
• 2654 Hob circular cutting command
• 2655 Hob cutting command
• 2657 SYSTEM VARIABLE C-axis connect
• 2658 B-axis independent encoder error
• 2659 NC tailstock position error
• 2662 NC TAILSTOCK no spec.
• 2663 Turning cut condition interlock
• 2667 X-axis mirror image coordinates selected
• 2668 X-axis mirror image coordinates impossible
• 2671 C-axis sync control no spec.
• 2672 C-axis sync command format
• 2674 Default status macro cannot be executed
• 2675 Tool posture command error
• 2676 Tool posture command angle conversion error
• 2677 Attachment change not possible
• 2678 SPM contour control not possible
• 2679 Mistake in Q command
• 2682 Magnetic encoder speed detection error
• 2683 MCS Rotary encoder 5 initialization failure
• 2684 MCS Rotary encoder 5 error
• 2685 MCS Rotary encoder 4 initialization failure
• 2686 MCS Rotary encoder 4 error
• 2687 MCS Rotary encoder 3 initialization failure
• 2688 MCS Rotary encoder 3 error
• 2689 MCS Rotary encoder 2 error
• 2690 MCS Rotary encoder 1 initialization failure
• 2691 MCS Rotary encoder 1 error
• 2692 MCS Linear scale 4 initialization failure
• 2693 MCS Linear scale 4 error
• 2694 MCS Linear scale 3 initialization failure
• 2695 MCS Linear scale 3 error
• 2696 MCS Linear scale 2 initialization failure
• 2697 MCS Linear scale 2 error
• 2698 MCS Linear scale 1 initialization failure
• 2699 MCS Linear scale 1 error
• 2700 No workpiece confirmation error
• 2701 Sequencer Error
• 2702 Spindle command during C-axis connection
• 2703 Chucking miss
• 2704 Chucking miss air off order impossible
• 2705 Tailstock quill over advance
• 2706 Polygon cutting command condition
• 2707 Invalid command during polygon cutting
• 2708 Invalid rotation tool gear
• 2709 Sub-spindle synchronization interlock
• 2710 Sub-spindle synchronization cutting
• 2711 Door open
• 2712 ATC no spec.
• 2713 Invalid ATC syntax
• 2714 Invalid ATC TC no.
• 2716 Invalid ATC TL no.
• 2717 Invalid ATC MT no.
• 2718 Invalid ATC MG no.
• 2719 Invalid ATC command
• 2720 M06/M228 interlock
• 2721 Turret number mismatch
• 2722 Robot/Loader request illegal
• 2723 ATC next tool preparation interlock
• 2724 Invalid ATC sub arm
• 2725 Invalid RS tool L/M
• 2726 Magazine encoder read
• 2727 Magazine rotation interlock
• 2728 Invalid magazine tool no.
• 2729 No magazine return pot
• 2730 Tool insertion interlock
• 2732 Tailstock sleeve position data error
• 2733 Coolant flow
• 2734 Coolant level
• 2735 Spindle low rotation command
• 2736 SVP time constant switching no spec.
• 2737 Invalid tailstock switch position
• 2738 Synchronous hobbing interlock
• 2739 Invalid synchronous hobbing mode
• 2740 Incorrect magazine tool data
• 2741 Touch setter unlock time over
• 2742 Setup switch ON
• 2743 Irregular coolant level
• 2744 Tool breakage
• 2745 Low high-pressure coolant pressure
• 2746 Hydraulic oil unit error
• 2747 Index disable position
• 2748 CPU fan stop
• 2749 Hydraulic oil level lower limit
• 2750 Tool monitoring unit error detection
• 2751 Coolant/Oil mist command
• 2752 Air pressure
• 2753 Unable to change tool
• 2754 Invalid coolant command
• 2755 Semi-dry unit error
• 2756 Actual tool data setting
• 2757 Oil mist unit error
• 2758 Invalid position data
• 2759 Coolant discharge error
• 2760 Sub-spindle rotation tool interlock
• 2761 W-axis overlap mode
• 2762 Chucking miss
• 2763 Coolant filter
• 2764 Coolant error
• 2765 Chip conveyer filter clogged
• 2766 Invalid M-tool spindle command
• 2767 M-spindle low rotation interlock
• 2768 Program check mode interlock
• 2769 Invalid spindle control command
• 2770 SVP time constant switching command
• 2771 APC clamp confirmation
• 2772 APC system mode
• 2773 APC M command
• 2774 Thread cutting cycle interlock
• 2775 Sensor head interlock
• 2776 M command not completed
• 2777 Cross rail positioning sensor error
• 2778 Cross rail motor overload
• 2779 Axis lube motor overload
• 2780 Axis lube pressure ON confirmation
• 2781 No AT command
• 2782 Axis lube pressure OFF confirmation
• 2783 Oil hole motor overload
• 2784 Invalid MT command
• 2785 Invalid AT command
• 2786 No S command
• 2787 No SB command
• 2788 Invalid SB command
• 2789 Coolant tank filter clogged
• 2790 Shower coolant motor overload
• 2791 M spindle head cooling unit
• 2792 Invalid RH command
• 2793 Incorrect attachment index position
• 2794 Mist air lube unit
• 2795 Warming up error
• 2796 Sequence restart
• 2797 Axis interlock release
• 2798 Invalid BC command
• 2800 Alarm detected from externally connected device
• 2801 Turret rotation interlock
• 2802 Invalid long boring bar command
• 2803 ATC tool data setting
• 2804 Attachment control
• 2805 Limit confirmation impossible
• 2806 Door interlock
• 2807 Invalid M code
• 2848 Chip conveyer overload
• 2849 Sensor unit in interference range
• 2850 External request interlock
• 2851 Machine change M-code
• 2852 Hand open/close interlock
• 2853 Teaching operation interlock
• 2854 Machine linked M-code
• 2855 Coolant filter
• 2856 Coolant motor overload
• 2857 UNUSABLE M-code
• 2858 Hand slide advance interlock
• 2887 Coupling device interlock
• 2888 Lube tank level
• 2890 Workpiece clamp miss
• 2891 Tailstock air miss
• 2892 Unable to execute air shut-off command
• 2893 Hydraulic oil controller faulty
• 2894 Spindle lubricant controller error
• 2895 Coolant controller error
• 2896 No touch setter
• 2897 Unloader no spec.
• 2898 Unloader interference position
• 2899 Gauge error
• 2900 DIRECTION V variable
• 2901 DIRECTION Check address
• 2902 DIRECTION Data operation
• 2903 DIRECTION Character use
• 2904 DIRECTION Numerical data
• 2905 DIRECTION Parameter/point
• 2906 DIRECTION Register
• 2907 DIRECTION F
• 2908 DIRECTION E
• 2909 DIRECTION Sequence no.
• 2910 UNUSABLE G-code
• 2911 UNUSABLE M-code
• 2912 UNUSABLE Address character
• 2913 UNUSABLE Mnemonic
• 2914 UNUSABLE Left side direction
• 2915 EXPRESSION Calculation
• 2916 EXPRESSION Syntax
• 2917 EXPRESSION Right side
• 2918 EXPRESSION Left side
• 2919 EXPRESSION Buffer over
• 2920 VARIABLE Buffer over
• 2921 PROGRAM DIRECT Program name
• 2922 PROGRAM DIRECT V variable
• 2923 PROGRAM DIRECT Character use
• 2924 PROGRAM DIRECT G-code
• 2925 BRANCH Sequence name
• 2926 BRANCH Condition
• 2927 Parameter setting illegal
• 2928 Parameter playback impossible
• 2929 Register setting impossible
• 2930 Program plus var. limit over
• 2931 Program minus var. limit over
• 2932 Program request illegal
• 2933 Program request impossible
• 2934 Program external request impossible
• 2935 No program selection
• 2936 No program
• 2937 Program end code
• 2938 Program analysis complete
• 2939 SUB PROGRAM stack
• 2940 SUB PROGRAM Program name
• 2941 SUB PROGRAM Buffer over
• 2942 Command impossible while running
• 2943 Data file read
• 2944 Comment end code not found
• 2945 Equal does not exist
• 2946 No spec.
• 2948 DIRECTION Y
• 2949 DIRECTION Z
• 2950 DIRECTION D
• 2951 DIRECTION L
• 2952 DIRECTION SU
• 2953 DIRECTION Torque limit
• 2954 PROGRAM DIRECT M-code
• 2955 PROGRAM DIRECT Equal
• 2956 Machine change M-code
• 2957 G22 feed
• 2958 Main sequence
• 2959 Barrier limit
• 2960 User reserve code
• 2961 Calculation function no spec.
• 2962 Subscript function no spec.
• 2964 NC program selection
• 2965 EXPRESSION subscript
• 2966 M code time over
• 2967 Cycle time over
• 2968 Program selection
• 2969 G23 FEED
• 2970 DIRECTION X
• 2971 DIRECTION I
• 2972 DIRECTION J
• 2973 DIRECTION K
• 2974 PROGRAM DIRECT hexadecimal data
• 2975 PROGRAM DIRECT character string
• 2976 Stopper position data illegal
• 2977 Program selection unsuitable
• 2978 DIRECTION V
• 2979 DIRECTION C
• 2980 No decimal point
• 2981 DIRECTION Q
• 2982 Time over