Industrial manufacturing
Industrial Internet of Things | Industrial materials | Equipment Maintenance and Repair | Industrial programming |
home  MfgRobots >> Industrial manufacturing >  >> Industrial materials >> Metal

99.98% Pure Nickel Flat Wire – S-Annealed for Superior Performance

Nickel with highest degree of purity with the following features:


  • Very low levels of carbon (20 ppm) and sulfur (2 ppm) which tend to segregate at grain boundries resulting in hot shortening
  • Cleanliness, absence of non-metallic inclusions as Al, Ti or Si oxides
  • Low electrical resistivity at 20°C
  • High thermal conductivity at 20°C
  • Excellent formability
  • Low softening temperature (350°C)
  • Low recrystallization temperature (350°C)
  • Improved oxidation resistance: development of tightly adherent one-layer oxide scale instead of a two-layer costumary one, which tends to flake off due to mismatch in thermal expansion.
  • Properties

    Dimension

    PropertyValue

    Dimensions

    Flat wire: Width: 1-12 mm, Thickness: 0.1-2.5 mm

    Mechanical

    PropertyTemperatureValueComment

    Elastic modulus

    23.0 °C

    196 GPa

    Hardness, Vickers

    23.0 °C

    65 [-]

    max.

    Thermal

    PropertyTemperatureValue

    Recrystallization temperature

    350 °C

    Thermal conductivity

    23.0 °C

    90.9 - 91 W/(m·K)

    Electrical

    PropertyTemperatureValue

    Electrical resistivity

    23.0 °C

    7.1E-8 Ω·m

    Chemical properties

    PropertyValue

    Carbon

    2E-3 %

    Nickel

    99.98 %

    Sulfur

    2E-4 %

    Technological properties

    Property
    Application areas

    Flat wire: contact in batteries and electronic applications, batteries managment devices, laser ribbon bonding, ultrasonic ribbon bonding

    Heat Treatment

    Soft Annealed

    Processing history

    Ribbon of high purity nickel is produced by two processing routes: I. slitting of strip: thick coil is rolled down on a modren Bühler reversing to the required thickness. The strip is cut on a high precision slitting line. The minimum band width is 1.0 mm. II. Flat rolling of wire: wire is flat rolled using Bühler flat rolling mill to the thickness between 0.10 to 2.5 mm and width between 1.0 and 12.0 mm.

    Surface Finish

    Blank/Bare surface


    Metal

    1. Tungsten Wire History: From Edison’s Carbon Filaments to Modern AKS Alloys
    2. 99.98% Pure Nickel Rods & Wire – S-Annealed for High‑Performance Applications
    3. 99.98% Pure Nickel Rod & Wire – 1/2 Hard, Ultra-Low Carbon & Sulfur, High Conductivity, Superior Formability
    4. 99.98% Pure Nickel Rod & Wire – Full Hard, High Conductivity & Superior Oxidation Resistance
    5. 99.98% Pure Nickel Flat Wire – 1/2 Hard, Low Carbon & Sulfur, High Conductivity
    6. High-Purity 99.98% Flat Nickel Wire – Superior Strength & Performance
    7. 99.98% Purity Nickel Plate, Strip, Band, Foil – S-Annealed
    8. High-Purity 99.98% Nickel Plate, Strip, Band & Foil – 1/2 Hardness Grade
    9. 99.98% Pure Nickel Plates, Strips, Bands & Foils – Full Hard, High‑Performance Alloy
    10. Nickel 270 – Commercially Pure, Unalloyed Nickel for Industrial Use