DIN 1725-1 Grade 3.3316 H24 Aluminium-Magnesium Alloy – Superior Corrosion Resistance & Machinability

The alloys are characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a strength increase can be attained. It is well polishable and anodisable. The splinter-giving machinability becomes better with increasing Mg content, just as the weldability. From the AlMg alloys the mark AlMg1,5 has to exhibit only relatively small mechanical properties. Standardised semi-finished material only for sheet metal and strips with thickness: > 0.35 mm in accordance to DIN 1745. Application: The main application lies in the building industry. In the building industry for lamella net curtains, rolling shutter, roll gates, in food industry (including table-ware) and for transport containers.

Properties

General

Property	Temperature	Value	Condition	Related Standards	Shape
Density		2.68 g/cm³	H24	EN 573-3, EN 485
		2.69 g/cm³	H24	EN 573-3, EN 485
	20.0 °C	2.69 g/cm³	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat

Mechanical

Property	Temperature	Value	Condition	Related Standards	Shape	Comment
Bending angle 180°		1.5 °/t	H24	EN 573-3, EN 485
		2.0 °/t	H24	EN 573-3, EN 485
Bending angle 90°		0.5 °/t	H24	EN 573-3, EN 485
		1.0 °/t	H24	EN 573-3, EN 485
		1.5 °/t	H24	EN 573-3, EN 485
		2.0 °/t	H24	EN 573-3, EN 485
Elastic modulus		69.0 GPa	H24	EN 573-3, EN 485
		70.0 GPa	H24	EN 573-3, EN 485
	20.0 °C	70.0 GPa	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
Elongation		3.0 %	H24	EN 573-3, EN 485		A50
		4.0 %	H24	EN 573-3, EN 485		A50
		5.0 %	H24	EN 573-3, EN 485		A50
		8.0 %	H24	EN 573-3, EN 485		A50
	20.0 °C	8.0 %	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat	A10
	20.0 °C	10.0 %	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
Hardness, Brinell		54.0 [-]	H24	EN 573-3, EN 485
	20.0 °C	55.0 [-]	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
Plane-Strain Fracture Toughnes		22.0 - 35.0 MPa·√m				Typical for Wrought 5000 Series Aluminium
Poisson's ratio		0.33 [-]				Typical for Wrought 5000 Series Aluminium
Shear modulus	20.0 °C	26.5	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
Tensile strength	20.0 °C	175.0 - 215.0 MPa	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat

Thermal

Property	Temperature	Value	Condition	Related Standards	Shape	Comment
Coefficient of thermal expansion	20 °C	2.38e-05 1/K	H24	EN 573-3, EN 485
	100 °C	2.38e-05 1/K	H24	EN 573-3, EN 485
Max service temperature		150.0 °C				Typical for Wrought 5000 Series Aluminium
Melting point		620.0 - 650.0 °C	H24	EN 573-3, EN 485
		625.0 - 650.0 °C	H24	EN 573-3, EN 485
Specific heat capacity		879.0 - 963.0 J/(kg·K)				Typical for Wrought 5000 Series Aluminium
Thermal conductivity		170.0 - 190.0 W/(m·K)	H24	EN 573-3, EN 485
		193 W/(m·K)	H24	EN 573-3, EN 485
	20.0 °C	160.0 - 200.0 W/(m·K)	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat

Electrical

Property	Temperature	Value	Condition	Related Standards	Shape
Electrical conductivity		23000000.0 - 26000000.0 S/m	H24	EN 573-3, EN 485
		29000000.0 S/m	H24	EN 573-3, EN 485
	20.0 °C	28000000.0 - 30000000.0 S/m	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
Electrical resistivity		3.45e-08 Ω·m	H24	EN 573-3, EN 485
		3.85e-08 - 4.35e-08 Ω·m	H24	EN 573-3, EN 485

Chemical properties

Property	Value	Condition	Related Standards	Shape
Chromium	0.1 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat
Copper	0.05 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat
Iron	0.45 %	H24	DIN 1725-1, EN 573-3, EN 573-4	Flat
	0.45 %	H24	EN 573-3, EN 485
Magnesium	1.1 - 1.7 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat
Manganese	0.15 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat
Silicon	0.4 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat
Zinc	0.2 %	H24	DIN 1725-1, EN 573-3, EN 573-4, EN 485	Flat

Technological properties

Property
Workability	Good workability.

Property

Workability

Good workability.

DIN 1725-1 Grade 3.3315 H24: High-Performance AlMg Alloy for Corrosion-Resistant Applications EN 573-3 Grade 3.3545 H14 – High-Strength, Corrosion-Resistant Aluminum Alloy

Metal