Electrical welded tubes made of the heat-resistant non-alloy quality steel P265GH are used for steam pressure vessels, tube construction, pressure vessel and apparatus manufacturing mainly in the chemical industry for temperatures up to 200 °C and simultaneous high pressures. The total load and the

Electrical welded tubes made of the heat-resistant non-alloy quality steel P235GH are used for steam pressure vessels, tube construction, pressure vessel and apparatus manufacturing mainly in the chemical industry for temperatures up to 200 °C and simultaneous high pressures. The total load and the

Steel P275NL2 is a particularly cryogenic weldable fine-grained construction steel (alloyed high-grade steel) for pressure vessel and steel construction.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212

Steel P275NL1 is a cryogenic weldable fine-grained construction steel (alloyed high-quality steel) for pressure vessel construction.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa20

Seamless tubes of the high-temperature P195GH are used in steam boiler and pipeline construction, pressure vessel and apparatus engineering, especially in chemical industry and power station construction at temperatures from approx. 200 °C to maximum 400 °C and simultaneously high pressures. The tot

S235J2G3 is a fine grained steel for welding constructions of high load. The steel is applicated up to temperatures of -20°C subject to the load. For this steel are available (mat. No 1.0118 acc. to DIN EN 10025) grades for: - folding (KQ)-S235J2G3C - cold forming of sections (KP)-S235J2G3C - cold

S355K2G3 is a high-tensile fine grained steel for welding constructions of dynamic load. The steel is applicated up to temperatures of -20°C. Mechanical properties in thickness direction have to comply with EURONORM 164. Compared to S235J2G3 is achievable a considerable saving of material due to the

S355J2G3 is a high-tensile fine grained steel for welding constructions of dynamic load. The steel is applicated up to temperatures of -20°C. Compared to S235J2G3 is achievable a considerable saving of material due to the by 120 MPa higher yield point. The steel shows a by 15% higher resistance to m

S275J2G3 is a fine grained steel for welding constructions of dynamic load. The steel is applicated up to temperatures of -20°C. Compared to S235J2G3 is achievable a saving of material due to the by 40 MPa higher yield point. For this steel are available (mat. No 1.0141 acc. to DIN EN 10025) grades

The fine grain steel TStE 420 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel TStE 355 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel TStE 285 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel TStE255 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel StE 460 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel StE 420 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel StE 355 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well

The fine grain steel StE285 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well a

The fine grain steel StE255 is used for special requirements according to DIN 17178 : 1986-5 for welded steel tubes and according to DIN 17179 : 1986-5 for seamless steel tubes. These steel tubes are used above all in pressure vessel construction, apparatus construction, pipe construction, as well a

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.7 g/cm³FEN 1706, EN 13195Casting20.0 °C2.7 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60.0

Steel C 22 is suitable for low strained parts of small heat treatment sections in vehicle manufacturing and machine engineering (e.g. piston-rods, gear wheels). Lowest application temperature -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.85 g/cm³MechanicalPropertyTemperature