The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a stre

The alloy Al99,85Mg1 belongs to the standardised glossing materials. It can be polished after preceding mechanical polishing chemically or electrolytically to high gloss. For using the high gloss surface a afterwards anodising is necessary. The degree of arranged reflection (gloss degree) dependents

The AlMg alloy is characterised all by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increase the strength, the cold forming capacity decreases with it. The alloys of this type are nature hard, i.e. only by a cold forming and not by a purposef

The alloy Al99,9Mg0,5 belongs to the standardised glossing materials. It can be polished after preceding mechanical polishing chemically or electrolytically to high gloss. For using the high gloss surface a afterwards anodising is necessary. The degree of arranged reflection (gloss degree) dependent

The alloy Al99,85Mg0,5 belongs to the standardised glossing materials. It can be polished after preceding mechanical polishing chemically or electrolytically to high gloss. For using the high gloss surface a afterwards anodising is necessary. The degree of arranged reflection (gloss degree) dependen

GD-AlMg9 is good polishable, applicable for anodic oxidising without decorative purpose. The machinability is excellent but no welding. It is applicable for parts with high demands on corrosion resistance and surface quality, for example in optical industry, office machines or household appliance Ha

DIN 3.3211 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.PropertiesGeneralPropertyValueConditionRelated Stan

GD-AlSi12 is a not hardenable eutectic alloy with excellent filling casting ability and high hot cracking resistance with high chemical resistance. It is especially applicable for higher loaded corrosion resistant and fatigue-strength cast pieces. Application: parts of machines, impact and fatiguing

G-AlSi12 is an eutectic alloy with excellent casting characteristics. It has a medium strength but good plasticity, is weather and corrosion resistant. The alloy is suitable for difficult shapes, thin-walled, impact loaded cast parts. Application: devices, machines, vehicle, ship and apparatus engin

G-AlSi11 - eutectic alloy - excellent ability for filling shapes and casting properties with high chemical resistance - high hot crack resistance - applicable for complex, thin walled, pressure tight and stable at vibration cast pieces with good corrosion resistance application: - parts of machines,

Good weldable cast material with good casting properties. Castings are sensitive to impact loads.Application: fittingsPropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.7 g/cm³T6WL 3.2134Casting20.0 °C2.7 g/cm³T6WL 3.2134MechanicalPropertyTemperatureValueConditionRelate

G-AlCu4TiMg - solidifies in an wide range of temperature - complicated casting - application in part hardend or warm hardend state - applicable for cast pieces, with high demands to strength (warm hardened) and highest toughness (cold hardened) application: - wear resistant construction parts in au

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.65 g/cm³T6EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110.0 MPaT6EN 1706, EN 13195Castin

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110.0 MPaFEN 1706, EN 13195CastingE

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³T64EN 1706Casting20.0 °C2.65 g/cm³T64EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 1

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³T6EN 1706Casting20.0 °C2.65 g/cm³T6EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³FEN 1706Casting20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110.0

Aluminium casting alloy (sand casting, permanent mould casting, investment casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.66 g/cm³T64EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110.0 MPaT64E

Aluminium casting alloy (sand casting, permanent mould casting, investment casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.66 g/cm³T6EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110.0 MPaT6EN

Aluminium casting alloy (sand casting, permanent mould casting, investment casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³T64EN 1706, EN 13195Casting20.0 °C2.65 g/cm³T64EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBe