PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C32 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

The material X8CrNiMoAl15-7-2 is comparable to X 7 CrNiMoAl 15 7 acc. to Key to steel 1995 resp. Register of European steel 1994. The precipitation hardenable steel with high strength and hardness shows good corrosion resistance. Application for clamps and springs, surface facings, bottoms for fuel

The material NiCr22Mo7Cu with the material number 2.4619 is applied for corrosion-resistant construction components in the form of strips, sheets, tubes, bars, wires and forgings. It is a further development of the material NiCr22Mo6Cu (material number 2.4618) and has an excellent resistant to pitti

The soft-magnetic material NiFe16CuCr with the material number 2.4501 distinguishes itself by the highest initial and maximum permeability as well as by the lowest coercive field strength. It is applied for transformers, e.g. for totalizing current transformers (for fault-current circuit breakers),

The expansion material NiFe46 with the material number 2.4475 is applied in sealings in soft glasses. It possesses a relatively low thermal expansion up to approximately 450 °C. (Temperature interval RT to 400 °C: coefficient of thermal expansion 9.8 to 10.6 10^-6 K^-1). . The alloy is of relative d

TH 550, mat. No 1.0373, is a double cold reduced band (black plate in coils) of soft unalloyed steel and in the surface qualities plain, stone finish and matt for conventional packaging sheet, hardness HR30T m max. 73. The band is produced in thicknesses of 0,17 to 0,29 mm in steps of 0,005 mm. The

Properties: - austenitic CrNi-steel with additives of nitrogen - similar corrosion properties like 1.4439, somewhat smaller pitting index - polishable Application: - for surgical instrumentsPropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.9 - 8.2 g/cm³Typical for Austenitic Stainless

The material NiCr6015 with the material number 2.4867 is applied in the form of strips and wires (see also heating conductor alloys according to DIN 17470 or electrical resistance alloys according to DIN 17471) for heating conductors and resistors. It is a nickel-iron-chromium heating conductor allo

PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series AluminiumMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series AluminiumPoisson's r

CuSn6, mat. No. CW425K, is comparable to the DIN-make CuSn6, mat. No. 2.1020, acc. to DIN 17662 : 1983-12. Properties of the CuSn-alloy are predominantly determined by the tin-content. Tensile strength, yield point and hardness increase according to the rising cold forming grade, elongation after fr

MP35N™ is a trademarked grade produced by Latrobe Speciality Steel, a subsidiary of Carpenter Technology in the USA, and the trademark is owned by SPS Technologies Inc. This data sheet covers material produced for optimum corrosion resistance and to comply with the requirements of NACE MR0175. It ha

Alloy 718 is a precipitation hardenable nickel chromium alloy. As the major alloy elements are molybdenum, niobium + tantalum, aluminium and titanium, Alloy 718 gives exceptionally high yield, good corrosion resistance, tensile and creep rupture properties at temperatures up to 700°C (1300F). Broder

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.6 - 7.7 g/cm³Typical for Martensitic Stainless SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C220 GPaTypical for Martensitic Stainless SteelElongation A5023.0 °C10 %Elongation A50, transverse23.0 °C6 %Hardness, Brin

DIMO C45 is an unalloyed carbon tool steel for the construction of plastic mold assemblies. DIMO C45 is supplied in a stress relieved condition with a normalized ferrite-pearlite-microstructure. The normalizing can be replaced by a normalizing rolling. Cut edges are stress relieved by an appropriate

UNS R56407 is similar to Grade 5 but has lower oxygen, nitrogen and iron. It has better ductility and fracture toughness than Titanium Grade 5.PropertiesGeneralPropertyValueRelated StandardsShapeDensity4.45 g/cm³AMS 4907, AMS 4930, AMS 6932, AMS T9046, AMS T9047Billet, TubeDimensionPropertyValue

PropertiesGeneralPropertyValueRelated StandardsShapeDensity4.5 g/cm³ASME SB-338Sheet, PlateDimensionPropertyValueRelated StandardsShapeLength1500 mmASME SB-338Sheet, Plate5000 mmASME SB-338Sheet6500 mmASME SB-338PlateWidth400 mmASME SB-338Sheet600 mmASME SB-338Plate1524 mmASME SB-338Sheet1600 mmASME

2.1525 (CuSi3Mn) is a high copper alloy that is renowned for its combination of strength, corrosion resistance and formability and for its attractive colour. Known as a high silicon bronze, COLDUR-A® (C65500) is renowned as being one of the easiest of all copper alloys to fabricate - by a wide range

Among the highest density element and melting point, rhenium does not have a ductile to brittle transition temperature and does not form carbides. With high resistivity, combined with low vapor pressure, it is an ideal material for filament applications. Excellent resistance to corrosion, resists ac

Cold rolled uncoated low carbon steel narrow strip for cold forming.,The non-alloy steel DC05 acc. to DIN EN 10130 is as special deep-draw quality suitable for cold forming of complexest profile forms, components and molded parts.To freedom of stretcher strains applies a period of 6 months after pro

G-X 260 NiCr 4 2, has a high wear resistance, usable at moderate impact stress.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C169 - 183 GPaHardness, Brinell20.0 °C430 - 690 [-]Hardness, Vickers20.0 °C450 - 750 [-]Poisson