Cold-rolled narrow strip made of the alloy steel 42CrMo4 will be delivered in thicknesses up to 6 mm for quenching and tempering and for quenched and tempered cold strip in thicknesses between 0.3 mm and 3.0 mm in following conditions: - soft annealed or soft annealed and little rerolled (+A or +LC)

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 g/cm³typical valueDimensionPropertyValueThickness16 - 250 mmMechanicalPropertyTemperatureValueCommentCharpy impact energy23.0 °C30 - 45 Jmin.Elastic modulus23.0 °C190 - 210 GPatypical valueElongation23.0 °C11 - 13 %min., A5.65Hardness

X45CrNiW18-9 is an austenitic Cr-Ni-W-alloyed valve steel. The steel shows sufficient corrosion resistance in exhaust condensate and good resistance to lead compounds at increased temperatures. Application at operating temperatures up to 730 deg. Use: exhaust valves, valvesPropertiesGeneralPropertyT

The expansion material NiFe48Cr possesses a relatively low thermal expansion at 450 °C. (Temperature interval RT to 400 °C: coefficient of thermal expansion 9.9 to 10.7 10^-6 K^-1). It is applied for sealings for soft glasses as well as as surge voltage protection. The alloy is of good durability at

WTSt 37-3 is used for welded, screwed and riveted constructions of different kind, e. g. structural engineering, bridge building, container construction. The steel is good weldable and formable.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueElastic

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C6 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear mo

The material NiMo23Cr8Fe with the material number 2.4710 is used in the form of strips, sheets, tubes, bars, wires and forgings for corrosion-resistant construction components. The material is a nickel-molybdenum-chromium-iron-solid solution alloy with outstanding corrosion-resistance in very acid m

The austenitic steel X2CrNi18-9 is available in solution annealed condition in the form of cold rolled strip, warm rolled strip and warm rolled sheet. The material is resistant to intercrystalline corrosion also in welded condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.9 g/cm³Mech

Amstrong® 420MC characterised by high ductility, controlled internal purity, fine grain structure and low carbon content. On request, Amstrong® may be delivered with an improved surface finish on black hot-rolled product called MASC (Micro Adhesive Scale). Contact our commercial teams for further in

Amstrong® 390MC characterised by high ductility, controlled internal purity, fine grain structure and low carbon content. On request, Amstrong® may be delivered with an improved surface finish on black hot-rolled product called MASC (Micro Adhesive Scale). Contact our commercial teams for further in

Amstrong® 355MC characterised by high ductility, controlled internal purity, fine grain structure and low carbon content. On request, Amstrong® may be delivered with an improved surface finish on black hot-rolled product called MASC (Micro Adhesive Scale). Contact our commercial teams for further in

Amstrong® 315MC characterised by high ductility, controlled internal purity, fine grain structure and low carbon content. On request, Amstrong® may be delivered with an improved surface finish on black hot-rolled product called MASC (Micro Adhesive Scale). Contact our commercial teams for further in

Amstrong® 280MC characterised by high ductility, controlled internal purity, fine grain structure and low carbon content. On request, Amstrong® may be delivered with an improved surface finish on black hot-rolled product called MASC (Micro Adhesive Scale). Contact our commercial teams for further in

DIWA 393 is a weldable fine grained steel for higher temperature service. It is characterised by high 0.2 % proof stress at elevated temperatures. DIWA 393 is produced using basic oxygen steelmaking process. Its properties are achieved by water quenching and tempering . DIWA 393 is applied as plate

Lebronze alloys is worldwide leader in the design, customization, and production of copper & nickel alloys. Lebronze alloys (LBA) is actively involved in proposing ethical and ecologically sustainable solutions. In brass applications, lead has been widely used to improve machining operations. Nowad

KHP®109 is a CuNiSn alloy. KHP®109 provides an excellent combination of high electrical conductivity and good strength.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentBendability 180°, bw23.0 °C3 [-]Bendability 180°, gw23.0 °C1.5 [-]Bendabilit

KHP®109 is a CuNiSn alloy. KHP®109 provides an excellent combination of high electrical conductivity and good strength.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentBendability 180°, bw23.0 °C2 [-]Bendability 180°, gw23.0 °C0.5 [-]Bendabilit

KHP®109 is a CuNiSn alloy. KHP®109 provides an excellent combination of high electrical conductivity and good strength.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentBendability 180°, bw23.0 °C1 [-]Bendability 180°, gw23.0 °C0 [-]Bendability

KHP®109 is a CuNiSn alloy. KHP®109 provides an excellent combination of high electrical conductivity and good strength.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentBendability 180°, bw23.0 °C0.5 [-]Bendability 180°, gw23.0 °C0 [-]Bendabilit

KHP®7025 is a CuNiSi (Corson type) alloy. KHP®7025 provides a high electrical conductivity combined with high strength and good resistance against stress-relaxation.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.8 g/cm³MechanicalPropertyTemperatureValueCommentBendability 180°, bw23.0 °C2.5