CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

Cold-rolled narrow strip made of the alloy steel 25CrMo4 will be delivered in thicknesses up to 6 mm for quenching and tempering and for quenched and tempered cold strip in thicknesses between 0.3 mm and 3.0 mm in following conditions: - soft annealed or soft annealed and little rerolled (+A or +LC)

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn30 (CW505L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn28. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

Properties: - stainless duplex-steel with elevated strength and hardness - very good resistance to general corrosion, pitting and crack corrosion Application: - for components in light construction with higher durability and higher reliability - for heat exchanger and pipelines in media with chlorid

Properties: - steel will be melted with cramped chemical analyse - high corrosion resistance to oxidising acids, especially to nitric acid Application: - in urea synthesis systems, for construction they are in contact with up to 70 % concentrated nitric acid and higher tempartures - in fertiliser in

The high temperature alloy steel X21CrMoV12-1 is used for larger preshaped components in the quenched and tempered condition in turbine and generator installations, in particular as shafts and discs. The steel is weldable if the relevant measures required are observed.PropertiesGeneralPropertyTemper

Fully austenitic steel of high scaling temp. of 1150°C in air (highest application temp. in air), warranted scaling resistance for wide and fast thermal fluctuation, but no resistance in reducing athmosphere. Excellent creep behaviour and high deformation resistance. Application for furnace componen

The material X10CrAlSi25, mat. No 1.4762 is a heat-resistant steel of max. scaling resistance at 1150 °C (highest application temp. in air). The steel is highly resistant to oxidizing, sulfureous athmosphere. Low resistance in nitrogenous, oxygen deficient gases. The temp. limit in permanent operati

The material X10CrAlSi18, mat. No 1.4742 is non-scaling up to max. 1000°C (highest application temp. in air). The steel is resistant to oxidizing, sulfureous gases and shows mean resistance in reducing and carburizing gases. Application for oven components, gadgetries and for single parts of mean me

The heat-resistant steel Stahl X10CrAlSi13, mat. No 1.4724 shows a max. application temperature of 850°C (highest application temp. in air). The material is resistant to oxidizing, sulfureous athmosphere and shows mean resistance to reducing and carburizing gases. Application for oven components, va

Aluminum JIS 5052 is a non-heat treatable alloy with excellent finishing qualities. JIS 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the

Aluminum JIS 5052 is a non-heat treatable alloy with excellent finishing qualities. JIS 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the

Aluminum JIS 5052 is a non-heat treatable alloy with excellent finishing qualities. JIS 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the