Alloy M25 from Materion Performance Alloys is a free machining, high performance copper alloy. M25’s properties minimize signal distortion in coaxial RF connectors and reduce power loss in circular connectors and contact probes. M25 is available in spooled or coiled wire product forms, and in differ

Alloy M25 from Materion Performance Alloys is a free machining, high performance copper alloy. M25’s properties minimize signal distortion in coaxial RF connectors and reduce power loss in circular connectors and contact probes. M25 is available in spooled or coiled wire product forms, and in differ

In addition to their excellent corrosion resistance which ensures a long service life for structures over several decades, the UGIGRIP® range provides a guarantee of: Higher mechanical properties than with conventional steel, which allows the use of smaller cross sections or a reduction in reinforce

In addition to their excellent corrosion resistance which ensures a long service life for structures over several decades, the UGIGRIP® range provides a guarantee of: Higher mechanical properties than with conventional steel, which allows the use of smaller cross sections or a reduction in reinforce

UGIMA® 4057 is a member of the UGIMA® family of improved machinability martensitic stainless steels. It is developed exclusively by Ugitech. Its properties are identical to those of 1.4057, except for its machinability which is even better than that of 1.4057: UGIMA® 4057’s new technological advan

UGI® HT286 is an austenitic iron-base alloy containing nickel, chromium, molybdenum and titanium. The titanium and small amount of aluminium it contains enables the alloy to be strengthened by precipitation of the Ni3 (Ti,Al) gamma prime phase, providing good mechanical properties from cryogenic tem

Strong and corrosion resistant material for header and plate applications Use the URL below for more information: Gränges productsPropertiesDimensionPropertyValueDimensions<p>Standard process capabilities:</p> <p>Width: 10-1400mm</p> <p>Thickness 0.050-3.18mm</p>

Superior strength, Heat-treatable material Use the URL below for more information: Gränges productsPropertiesDimensionPropertyValueDimensions<p>Standard process capabilities:</p> <p>Width: 10-1400mm</p> <p>Thickness 0.050-3.18mm</p>MechanicalPropertyValueCommentT

Standard alloy AA 3003 Use the URL below for more information: Gränges productsPropertiesDimensionPropertyValueDimensions<p>Standard process capabilities:</p> <p>Width: 10-1400mm</p> <p>Thickness 0.050-3.18mm</p>MechanicalPropertyValueCommentTensile strength190 M

Nickel with highest degree of purity with the following features: Very low levels of carbon (20 ppm) and sulfur (2 ppm) which tend to segregate at grain boundries resulting in hot shortening Cleanliness, absence of non-metallic inclusions as Al, Ti or Si oxides Low electrical resistivity at 20°C Hi

Nickel with highest degree of purity with the following features: Very low levels of carbon (20 ppm) and sulfur (2 ppm) which tend to segregate at grain boundries resulting in hot shortening Cleanliness, absence of non-metallic inclusions as Al, Ti or Si oxides Low electrical resistivity at 20°C Hi

Nickel with highest degree of purity with the following features: Very low levels of carbon (20 ppm) and sulfur (2 ppm) which tend to segregate at grain boundries resulting in hot shortening Cleanliness, absence of non-metallic inclusions as Al, Ti or Si oxides Low electrical resistivity at 20°C Hi

The EN AW-5505 alloy is used for special applications not covered by a European standard. EU standards do not specify its mechanical characteristics. Mechanical properties to be agreed with the customer. It has excellent corrosion resistance and surface finishing properties. Suitable for electrochem

Work hardenable alloy designed to produce a homogenous matt finish after chemical or electrochemical brightening or anodizing.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C2.68 g/cm³MechanicalPropertyTemperatureValueElastic modulus23.0 °C60 GPaShear modulus23.0 °C23.8 GPaThermalPropertyTemp

Very good corrosion resistance and workability. Very ductile in annealed condition.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C2.71 g/cm³MechanicalPropertyTemperatureValueElastic modulus23.0 °C69 GPaShear modulus23.0 °C26 GPaThermalPropertyTemperatureValueCommentCoefficient of thermal exp

Chromium is a lightweight blue-silvery white metal. The name chromium comes from the Greek chroma and means color.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C7.15 g/cm³Molar mass52 g/molMechanicalPropertyTemperatureValueElastic modulus23.0 °C294 GPaHardness, Vickers, 1023.0 °C180 - 250 [-

With its unique mechanical and chemical properties, molybdenum is an outstanding material that can meet the most exacting requirements. Because molybdenum possesses a very high melting point, a low coefficient of thermal expansion and a high level of thermal conductivity, it is used in many differen

1.3505 (100Cr6) is a bearing steel suitable for the manufacture of ball bearings, roller oil bearings and needle bearings. Durapur 3505 also used in mechanical engineering for components subject to wear, e.g. for pump shafts and for components in automobile injection systems. For this purpose, it is

The newly developed Printdur® HSA is characterized by the following properties: Good processability with LPBF. Printdur HSA is produced without the alloying element nickel. As a result, the safety regulations during the processing of the powder are significantly reduced. Significantly increased yie

1.3520 (100CrMnSi6-4) is used in the rolling bearing industry for balls and rollers up to 90mm in diameter, as well as rings up to a finished wall thickness of 50 mm.PropertiesGeneralPropertyValueDensity7.6 g/cm³MechanicalPropertyValueCommentElastic modulus210 GPaHardness, Brinell217 - 375 [-]Depend