Steel CK 35 is suitable for a little higher strained parts in vehicle manufacturing and machine engineering with higher dimensions (heavy forged parts) and complexer forms as well as higher uniformity requirements on qualities and surface appearance (e.g. transmission parts, crankshafts). Lowest app

Steel C 60 is suitable for high ductility parts and parts of increased wear resistance requirements in vehicle manufacturing, engine and machine engineering surface hardenable (e.g. transmission parts, shafts, axles). Additional application in tooling. Lowest application temp. -25 °C.PropertiesGene

Steel C 45 is suitable for mean strained parts in vehicle manufacturing, engine and machine engineering (e.g. transmission shafts, gear wheels, transmission parts). Lowest application temp. -25 °C, favorable creep behaviour up to 480 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 g/cm

Steel C 35 is suitable for parts in vehicle manufacturing, engine and machine engineering with a little higher strength requirements and still low ductility requirements (e.g. gears, bolts, clutch parts). Lowest application temp. -25 °C, favorable creep behaviour up to 480 °C.PropertiesGeneralProper

PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 6000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus70.0 GPaTypical for Wrought 6000 Series AluminiumElongation9.0 %T5ASTM B241Pipe10.0 %T5ASTM B241PipeA50Hardness, Rockwell E89.0 [-

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation10.0 %H112; Area through 20000 mm2ASTM B241Tube12.0 %H112

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation12.0 %O; Area through 20000 mm2ASTM B241Tube14.0 %O; Area

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation10.0 %H112; Area through 20000 mm2ASTM B241Tube12.0 %H112

Additional services: Cuttings, Parts from drawings ALUDIUMMANUFACTURERInformation and servicesQuantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process op

Additional services: Cuttings, Parts from drawings ALUDIUMMANUFACTURERInformation and servicesQuantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process op

Additional services: Cuttings, Parts from drawings ALUDIUMMANUFACTURERInformation and servicesQuantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process op

PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumElongation22.0 %OASTM B241Tube25.0 %OASTM B241TubeA50Plane-Strain Fracture

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation22.0 %OASTM B211Bar, Rod, Wire25.0 %OASTM B211Bar, Rod, W

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation10.0 %H111; Area through 20000 mm2ASTM B241Tube12.0 %H111

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumElongation10.0 %H111; Area through 20000 mm2ASTM B241Tube12.0 %H111

Seamless tubes of the high-temperature 25CrMo4 are used in steam boiler and pipeline construction, pressure vessel and apparatus engineering, especially in chemical industry and power station construction at temperatures from approx. 200 °C to maximum 400 °C and simultaneously high pressures. The to

Seamless tubes of the high-temperature 20CrMoV13-5-5 are used in steam boiler and pipeline construction, pressure vessel and apparatus engineering, especially in chemical industry and power station construction at temperatures from approx. 200 °C to maximum 400 °C and simultaneously high pressures.

CuSn8, mat. No. CW453K, is comparable to the DIN-make CuSn8, mat. No. 2.1030, acc. to DIN 17662 : 1983-12. Properties of the CuSn-alloy are predominantly determined by the tin-content. Tensile strength, yield point and hardness increase according to the rising cold forming grade, elongation after fr

CuBe2, mat. No CW101C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuBe2, mat. No 2.1247, acc. to DIN 17666 : 1983-12 applies: It is an alloy of optimal hardenability for highest requirements to strength, elasticity, abrasion and fatigue resistance. CuBe2 shows mea

The weather resistant steel S235J2W with improved atmospheric corrosion resistance (by generation of an conversion coating) has a minimum yield strength of 235 N/mm². It is applicated for welded, screwed and riveted constructions, e.g. structural engineering, bridge building, tank construction, exha