Tungsten has the highest melting point of all metals and is therefore also suitable for very high-temperature applications. It is also characterized by a uniquely low coefficient of thermal expansion and a very high level of dimensional stability. PropertiesGeneralPropertyTemperatureValueDensity23.

PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.73 g/cm³H38EN 573-3, EN 1592Strip, Sheet, Plate, Foil, Bar, Rod, TubeMechanicalPropertyValueConditionRelated StandardsShapeCommentBending Fatigue Strength75.0 MPaH38EN 573-3, EN 1592Strip, Sheet, Plate, Foil, Bar, Rod, TubeElastic

Aluminum AA 5052 is a non-heat treatable alloy with excellent finishing qualities. AA 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the be

Aluminum AA 5052 is a non-heat treatable alloy with excellent finishing qualities. AA 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the be

Aluminum AA 5052 is a non-heat treatable alloy with excellent finishing qualities. AA 5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of the be

Aluminum AA 5005 is a lean aluminum magnesium alloy with low density and excellent thermal conductivity. This medium strength non-heat-treatable alloy is known for its corrosion resistance in alkaline marine situations. Aluminum AA 5005 is readily machinable, and can be welded using TIG and MIG meth

Aluminum AA 2024, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneralPro

2.1504 (CuNi14Al3) is an extra high strength copper nickel alloy developed by Columbia Metals that maximises both strength and corrosion resistance. Sometimes referred to as a nickel bronze, NIBRON® contains additions of aluminium, iron and manganese that join with the copper and nickel to achieve i

DEF STAN 02-835 Copper Alloy is a hot forged, stress relieved high strength cupronickel developed primarily for marine and offshore applications. The alloy contains around 14.5% nickel, 4.5% manganese and smaller additions of aluminium and iron to increase the overall material strength and corrosion

2.0966 (CuAl10Ni5Fe4) is a nickel aluminium bronze manufactured to the exacting requirements of the Ministry of Defence (MoD) that shows the following features and properties: Outstanding resistance to erosion and corrosion High strength and toughness High wear and galling resistance Non-sparking U

Commercially pure, unalloyed Nickel.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.89 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C207 GPaElongation23.0 °C40 %in 2 in.Hardness, Rockwell B23.0 °C80 [-]Tensile strength23.0 °C449 MPaYield strength23.0 °C138 MPaThermalPr

A controlled expansion alloy, consisting of 51% Nickel, balance Iron.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.3 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C159 GPaElongation23.0 °C35 %in 2 in.Hardness, Rockwell B23.0 °C80 [-]Tensile strength23.0 °C552 MPaYield

A controlled expansion alloy, consisting of 46% nickel, balance iron.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.17 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C159 GPaElongation23.0 °C30 %in 2 in.Hardness, Rockwell B23.0 °C80 [-]Tensile strength23.0 °C552 MPaYiel

Super Invar 32-5 is a low expansion alloy consisting of 32% nickel, 5% cobalt, and balance iron. Super Invar Alloy exhibits minimum thermal expansion at room temperatures (one half of Invar Alloy), as well as thermal expansion properties less than that of Invar Alloy in the 67/203°F (-55/95°C) tempe

Quend 1100 is extra high strength structural steel produced as quenched and tempered with a minimum yield strength of 1100 MPa.PropertiesGeneralPropertyValueCarbon equivalent (CET)0.36 [-]Carbon equivalent (CEV)0.57 [-]Carbon equivalent noteCEV = C+Mn/6+ (Ni+Cu)/15+ (Cr+Mo+V)/5 and CET = C+(Mn+Mo)/1

UGI® 4542 is a PH (Precipitation Hardening) martensitic stainless steel used for parts requiring a combination of high strength, high toughness and good corrosion resistance. This stainless steel is unique in that it not only offers excellent corrosion resistance, comparable to that of type 1.4301/

Properties: - corrosion characteristics comparable with those of 1.4571 - increased corrosion resistance to not-oxidizing acids and halogen containing media - not high polishable Application: - certified for constrcution of pressure tanks to 300 °C, until 550 °C, if no disintegration of grains-relea

Properties: - due to the high molybdenum content (over 3%), steel possesses very good resistance to not-oxidizing and halogen containing media - high polishable and able for cold forming Application: - in the chemical apparatus engineering, particularly in the pulp industry, the textile and rayon in

Properties: - corrosion behaviour is similar to 1.4401 - due to the higher Mo-content it possesses a something improved resistance to selective attack Application: - for acid-proof apparatuses of the chemical and pharmaceutical industry - in cellulose, pigment, fatty acid, textile and rayon industry

Properties: - full austenitic steel, which exhibits higher strength and structural stability in additive of nitrogen - higher resistance to oxidising media - nitrogen increases the effect sum (pittingindex) - high polishable - wel corrosion resistant to selective attack particularly in the welded c