Material X 2 CrNiMoN 17 13 5 (now: X2CrNiMoN17-13-5), material number 1.4539, is applicated acc. to VdT_V-Wbl 405 : 2000-12 for pressure vessels acc. to TRB 100 and AD-data sheets W 2 and W 10 from -196 to 400 deg. and for pressure gas tanks as per TRG 201 and TRG 203 from -196 to 400 deg. Further a

Material X2CrNiMoN17-13-3 is comparable to X 2 CrNiMoN 17 13 3 acc. to DIN 17440 : 1985-07. It is a fully austenitic steel that is suitable for mirror finishing. It shows higher strength owing to nitrogen alloying and owing to more molybdenum addition higher corrosion resistance especially to non ox

Material X2CrNiMo18-14-3 is comparable to X 2 CrNiMo 18 14 3 acc. to DIN 17440 : 1985-07. This material is a variant of 1.4404 with slightly increased alloying contents of Cr, Ni and Mo, therefore improved corrosion properties. It is resistant to intercrystalline corrosion also in sensitized conditi

Properties: - due to the low C-content, very good resistant to intergranular corrosion also in the welded condition to 400 °C - resistant to chloride containing media, oxidising and reducing acids (contaminated inclusively) - by the copper content the application is very well possible in sulfur-sour

Properties: - more with Mo alloyed as 1.4539 - possesses a very high resistance to intergranular corrosion, pitting corrosion and crack corrosion - it has the highest effect sum (Pittingindex) of the steel with 46 Application: - in highly chloride containing media, e.g. in appropriate sulfur and pho

Properties: - martensitic stainless steel - good corrosion resistance and very low-temperature toughness to -200 °C - possesses a high corrosion resistance, in particular to water, weak acids and brine, oxidising acids (nitric acid) and weakly chloride containing media Application: - for mechanical

Properties: - N-content lets increase the corrosion resistance, compared with 13%-Cr-steels - good toughness between -60 and 300°C and sufficient corrosion resistance - application in quenched and tempered state Application: - for turbine runner, compressors, pumps - components for plants and nuclea

The ferritic chrome steel X10CrAlSi7, mat. No 1.4713, shows very high resistance to oxidizing sulphureous gases, it is unsuitable for oxygen deficient and nitrogenous gases. Temperature limit for permanent operation accounts for 700 °C, scaling resistance up to 800 °C (highest application temperatur

CuZn40 (CW509L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn37. Corrosion resistance is similar to pure copper. Processing properties: warm forming: very good cold forming: goo

The heat-resistant steel Stahl X15CrNiSi25-4, mat. No 1.4821 shows a max. resistance up to 1100 °C (highest application temp. in air). The material is resistant to oxidizing, sulfureous gases shows resistance to reducing, sulfureous, carburizing, nitrogenous and oxygen deficient gases. Application i

The ferritic chrome steel X10CrAlSi7, mat. No 1.4713, shows very high resistance to oxidizing sulphureous gases, it is unsuitable for oxygen deficient and nitrogenous gases. Temperature limit for permanent operation accounts for 700 °C, scaling resistance up to 800 °C (highest application temperatur

EN-GJL-350 is used for high loaded machine and apparatus components, for machine tools and compressors.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.3 g/cm³MechanicalPropertyTemperatureValueCommentCompressive yield strength20.0 °C962 - 1237 MPaCompressive yield strength, 0.1%20.0 °C455 MP

EN-GJL-300 is used for cast parts for general mechanical engineering, e.g. shipbuilding, machine-tools, textile machines, electrotechnical engineering, apparatus engineering, farm machines, household machines, car engineering, pumps, turbine casings, fittings.PropertiesGeneralPropertyTemperatureValu

EN-GJL-250 is used for cast parts for general mechanical engineering, e.g. shipbuilding, machine-tools, textile machines, electrotechnical engineering, apparatus engineering, farm machines, household machines, car engineering, pumps, turbine casings, fittings.PropertiesGeneralPropertyTemperatureValu

EN-GJL-200 is used for various molded parts, precision castings, furnaces as well as for radiators.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.15 g/cm³MechanicalPropertyTemperatureValueCommentCompressive yield strength20.0 °C636 - 954 MPaCompressive yield strength, 0.1%20.0 °C260 MPaEla

EN-GJL-150 is used for various molded parts, precision castings, furnaces as well as for radiators.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.1 g/cm³MechanicalPropertyTemperatureValueCommentCompressive yield strength20.0 °C510 - 850 MPaCompressive yield strength, 0.1%20.0 °C195 MPaElas

The for pressure vessels approved steel X2CrNiMo18-15-4, mat. no. 1.4438, shows very good resistance to not oxidising media and halogenated media because of the high amount of Mo, is high polishable and good cold formable is resistant to intercrystalline corrosion in the delivery condition up to 6 m

The material X17CrNi16-2, mat. no. 1.4057, is used acc. DIN 17440 : 1996-09 for rods (for pressure vessels), forgings and drawn wire. For the application acc. DIN 17440 : 1985-07 (X 20 CrNi 17 2) resp. acc. DIN EN 10088-1,-2,-3 : 1995-08 (X17CrNi16-2) applies: The quench and temperable grade (17 % C

Steel C60 is usable for parts of high strength and increased requirements to abrasion resistance in vehicle, engine and machine engineering, surface hardenable (e.g. transmission parts, shafts, axles). Further application in tool making.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 g/cm

Steel C55 is usable for higher loaded parts in vehicle, engine and transmission engineering requiring improved abrasion resistance. Preferred application for parts undergoing a surface hardening. Lower cracking risk for larger and complexer parts than C60 (e.g. transmission wheels, shafts, anvil rol