Aluminum EN AW-3003 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, EN AW-3003 is weldable by conventional welding me

Aluminum EN AW-2024, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

Aluminum EN AW-2024, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

Aluminum EN AW-2024, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.4 [-]max. for t ≤ 50 mm plate thickness0.42 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.4 [-]max. for t ≤ 50 mm plate thickness0.42 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.4 [-]max. for t ≤ 50 mm plate thickness0.42 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.38 [-]max. for t ≤ 50 mm plate thickness0.4 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.38 [-]max. for t ≤ 50 mm plate thickness0.4 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.38 [-]max. for t ≤ 50 mm plate thickness0.4 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Higher-strength Hull Structural SteelPropertiesGeneralPropertyValueCommentCarbon equivalent (CET)0.38 [-]max. for t ≤ 50 mm plate thickness0.4 [-]max. for 50 < t ≤ 100 mm plate thicknessDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyTemperatureValueCommentCharpy impact energy

Aluminum EN AW-3003 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, EN AW-3003 is weldable by conventional welding me

This cold and hot hardenable material reaches mechanical strength of 200 to 250 MPa with A5-elongation at break of approx. 10 %. In warm and/or cold-hardened condition is this alloy only limited formable, in the soft material condition however well. Weldability, corrosion resistance and anodisingab

The steel RRStE 210.7 is produced as seamless or welded tube in the conditions untreated or normalised. Tubes of this steel are conform acc. 5L, 5LX and 5LS of the American Petroleum Institute (API). The Attention should be paid to the technical regulation for combustible liquids TRbF 301. Applica

The alloy Al99,85MgSi belongs to the standardised aluminum shining materials. Aluminum alloys being based on aluminum with a minimum purity of 99,85 %, can be polished after mechanical polishing chemically or electrolytically to high gloss. The produced gloss degree must, in order to remain preserve

The steel RRStE 240.7 is produced as seamless or welded tube in the conditions untreated or normalised. Tubes of this steel are conform acc. 5L, 5LX and 5LS of the American Petroleum Institute (API). The Attention should be paid to the technical regulation for combustible liquids TRbF 301. Applica

Non-heat-treatable aluminium alloy used for rivets in joints of Mg alloys and AlMg alloys.The material has a better corrosion resistance, particularly sea-water resistance, than other Al riveted joints and is capable of being permanently headed.PropertiesGeneralPropertyTemperatureValueConditionRelat

The alloy Al99,9MgSi belongs to the standardised aluminum shining materials. Aluminum alloys being based on aluminum with a minimum purity of 99,85 %, can be polished after mechanical polishing chemically or electrolytically to high gloss. The produced gloss degree must, in order to remain preserved

Food safe aluminum.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.71 g/cm³F12EN 573-320.0 °C2.71 - 2.72 g/cm³F12EN 573-320.0 °C2.72 g/cm³F12EN 573-3MechanicalPropertyTemperatureValueConditionRelated StandardsCommentElastic modulus20.0 °C60.0 - 65.0 GPaF12EN 573-32

High mechanical properties, oxidation resistant, saline mist corrosion resistant.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C7.5 g/cm³MechanicalPropertyTemperatureValueElastic modulus23.0 °C125 GPaElongation23.0 °C8 %Hardness, Brinell23.0 °C185 [-]Hardness, Rockwell C23.0 °C12 [-]Hardness