The austenitic-ferritic steel X2CrNiMoCuN25-6-3 will be delivered in the solution annealed condition as cold rolled strip, hot rolled sheet and strip, wire rod and profiles. It shows resistance to intercrystalline corrosion even in sensitized condition.PropertiesGeneralPropertyTemperatureValueDensit

The austenitic steel X2CrNiMo18-15-4 shows very high resistance to unoxidizing and halogenated media due to its high Mo-content (more than 3%), furthermore resistance to intercrystalline corrosion even in sensitized condition. It is usable for mirror-polishing and is cold formable. The steel is perm

The austenitic steel X2CrNiMo18-14-3 is a variant of 1.4404 of slightly higher alloying contents for Cr, Ni and Mo and because of that with enhanced corrosion qualities. It is resistant to intercrystalline corrosion even in sensitized condition and weldable. Application: in apparatus engineering, ch

Steel C55 is suitable for higher strained parts in vehicle, engine and transmission manufacturing that require an enhanced wear resistance. Preferred application for parts undergoing a surface hardening lower risk of tearing for larger and complexer parts than C60 (e.g. transmission gear wheels, sh

Steel C 50 is suitable for parts in vehicle manufacturing, engine and machine engineering with higher strength and wear resistance requirements (e.g. shafts, hubs). Lowest application temp. -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureVal

Steel C 45 is suitable for mean strained parts in vehicle manufacturing, engine and machine engineering (e.g. transmission shafts, gear wheels, transmission parts). Lowest application temp. -25 °C, favorable creep behaviour up to 480 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.

Steel C 40 is suitable for larger forged parts in vehicle manufacturing and machine engineering (e.g. road wheels, axles). Lowest application temp. -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C21

Steel C 35 is suitable for parts in vehicle manufacturing, engine and machine engineering with a little higher strength requirements and still low ductility requirements (e.g. gears, bolts, clutch parts). Lowest application temp. -25 °C, favorable creep behaviour up to 480 °C.PropertiesGeneralProper

Submerged-arc welded tubes made of the heat-resistant alloy high-grade steel 16Mo3 are used for steam pressure vessels, tube construction, pressure vessel and apparatus manufacturing mainly in the chemical industry for temperatures up to 200 °C and simultaneous high pressures. The total load and the

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

Electrical welded tubes made of the heat-resistant alloy high-grade steel 16Mo3 are used for steam pressure vessels, tube construction, pressure vessel and apparatus manufacturing mainly in the chemical industry for temperatures up to 200 °C and simultaneous high pressures. The total load and the sp

6 mm. Large-scale application for welded parts in chemical apparatus engineering as well as in food, luxury food, fat and soap industry, in film and photo industrie, in leather and sugar factories and for household articles. Application up to 550 deg. if there are no media causing intercrystalline a

Material X6CrNiNb18-10 is comparable to X 6 CrNiNb 18 10 acc. to DIN 17440: 1985-07. Its corrosion properties are comparable to 1.4541. The steel is resistant to intercrystalline corrosion also in sensitized condition, but it shows heat-crack susceptibility under certain welding conditions. Widely a

The austenitic steel X6CrNiTiB18-10 is a high temperature resistant steel for pressure vessels and steam-boiler construction as well as power plant engineering. The material is resistant to intercrystalline corrosion, also in the sensitized condition. The steel is according to DIN EN 10095 usable as

Material X6CrNiMoNb17-12-2 is comparable to X 6 CrNiMoNb 17 12 2 acc. to DIN 17440 : 1985-07. Its corrosion properties are comparable to 1.4571. Increased corrosion resistance to non oxidizing acids and halogenated media. This material is resistant to intercrystalline corrosion also in sensitized co

Material X5CrNiMo17-12-2 is comparable to X 5 CrNiMo 17-12-2 acc. to DIN 17440 : 1985-07 (ungültig). This material is an austenitic CrNiMo-steel with increased resistance to non oxidizing acids and halogenated media but to intercrystalline corrosion only in delivery condition. It is suitable for mir

X5CrNi18-10 as a standard type of the CrNi-steels is comparable to X 5 CrNi 18 10 acc. to DIN 17440 : 1985-07 (invalid). It shows high corrosion resistance but no resistance to intercrystalline corrosion in sensitized condition. It is resistant in delivery condition. The steel is well processable, s

Steel X2NiCrAlTi32-20, material number 1.4558 is applicated acc. to VdT_V-material specification 474 : 1984-12 for heat exchanger pipes for use as U-pipes in steam generators for pressurized water reactors (grit size-index acc. to EN 103 at least 7 at the straight pipe) for temperatures from -10 to

The austenitic CrNi-steel X2CrNiN18-10, comparable to X 2 CrNiN 18 10 acc. to DIN 17440 : 1985-07 (invalid), shows a higher yield point by nitrogen alloying which survives also at higher temperatures. This is used in pressure vessel and leightweight construction. Improvement of the corrosion resista

CuZn30 (CW505L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn28. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo