Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommen

Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommen

Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommen

Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommen

The steel 71 Si 7 is used for highest loaded tension springs in the clock engineering and similar applications up to 3.0 mm sheet thicknesses.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.78 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C206 - 212 GPa100.0 °C

Properties: better corrosion resistance compared with normal 13%-Cr-steel, because of its higher Cr-content and Mo-content Application: - for surgical instruments and fractional hardened elementsPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 g/cm³MechanicalPropertyTemperatureValueComment

The soft non-alloy steel USt 3 is suited for cold forming and is offered in different conditions (K to K60) with different strength and depth indications. The steel is applicated in the plant and tool engineering. Free from stretcher lines for 4 weeks is garuanteed in the LG and K32 condition. No st

The soft non-alloy steel USt 3 is suited for cold forming and is offered in different conditions (K to K60) with different strength and depth indications. The steel is applicated in the plant and tool engineering. Free from stretcher lines for 4 weeks is garuanteed in the LG and K32 condition. No st

The soft non-alloy steel St 4 is suited for cold forming and is offered in different conditions (K to K60) with different strength and depth indications. The steel is applicated in the plant and tool engineering. Free from stretcher lines for 4 weeks is garuanteed in the LG and K32 condition. No str

The soft non-alloy steel St 2, St 12 acc. to DIN 1623/1, is suitable for cold forming. The steel is offered in different conditions (from K to K70) with different strength and cupping values. The steel is applicated in the plant and tool engineering. No stretcher lines in the conditions K40 to 70. T

The soft non-alloy steel St 2, St 12 acc. to DIN 1623/1, is suitable for cold forming. The steel is offered in different conditions (from K to K70) with different strength and cupping values. The steel is applicated in the plant and tool engineering. No stretcher lines in the conditions K40 to 70. T

The soft non-alloy steel RRSt 3 is suited for cold forming and is offered in different conditions (K to K60) with different strength and depth indications. The steel is applicated in the plant and tool engineering. Free from stretcher lines for 4 weeks is garuanteed in the LG and K32 condition. No s

The soft non-alloy steel RRSt 3 is suited for cold forming and is offered in different conditions (K to K60) with different strength and depth indications. The steel is applicated in the plant and tool engineering. Free from stretcher lines for 4 weeks is garuanteed in the LG and K32 condition. No s

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelPoisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear modulus23.0 °C82 GPaTy

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelPoisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear modulus23.0 °C82 GPaTy

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelPoisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear modulus23.0 °C82 GPaTy

CuSn4, mat. No. CW450K, is comparable to the DIN-make CuSn4, mat. No. 2.1016, acc. to DIN 17662 : 1983-12. The material is specified by a favorable combination of very good cold formability with strength and hardness. It is corrosion resistant, good soft and hard solderable and shows still good elec

CuBe2, mat. No CW101C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuBe2, mat. No 2.1247, acc. to DIN 17666 : 1983-12 applies: It is an alloy of optimal hardenability for highest requirements to strength, elasticity, abrasion and fatigue resistance. CuBe2 shows mea

Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for High Carbon SteelMechanicalPropertyTemperatureValueCommentE

Non-alloy steel wire rod for drawing and/or cold rolling with specific requirements for special applications (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for High Carbon SteelMechanicalPropertyTemperatureValueCommentE