Sandvik 3R65 is a molybdenum-alloyed austenitic stainless chromium-nickel steel with a low carbon content. Datasheet URL: Sandvik 3R65 Datasheet updated 2019-08-26 09:14 (supersedes all previous editions)PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C8 g/cm³Recycled Content82.1 %Ave

Sandvik SAF 2304® is a lean duplex (austenitic-ferritic) stainless steel characterized by the following properties: Very good resistance to stress corrosion cracking (SCC) Good resistance to general corrosion and pitting High strength - approximately twice the proof strength of austenitic stainless

Sandvik 6R44 is an austenitic, niobium-stabilized stainless chromium-nickel steel for use at temperatures up to 850°C (1560°F). Datasheet URL: Sandvik 6R44 Datasheet updated 2019-09-02 09:19 (supersedes all previous editions) PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.9 g/cm³R

Sandvik 8R40 is an austenitic, niobium-stabilized stainless chromium-nickel steel for use at temperatures up to 850°C (1560°F). Datasheet URL: Sandvik 8R40 Datasheet updated 2019-09-02 09:20 (supersedes all previous editions) PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.9 g/cm³R

Sandvik 254 SMO is a high-alloy austenitic stainless steel developed for use in seawater and other aggressive chloride-bearing media. The steel is characterized by the following properties: Excellent resistance to pitting and crevice corrosion, PRE = ≥42.5 (The PRE is defined as, in weight-%, PRE =

This heat-treated alloy is the ultimate in high-strength bronzes requiring good bearing characteristics and exceptional wear resistance. It has greater toughness than grade AMPCO® 18.22 and better physical properties than grades AMPCO® 18 or AMPCO® 18.136. Its exceptional proportional limit gives i

Sanicro® 30 is a low-carbon version of Alloy 800 austenitic nickel-iron-chromium alloy. The grade is used for steam generator tubing in nuclear stations (PWR) and other heat exchangers for temperature up to about 550°C (1020°F) where good resistance to stress corrosion cracking (SCC) and intergranul

Sanicro® 30 is a low-carbon version of Alloy 800 austenitic nickel-iron-chromium alloy. The grade is used for steam generator tubing in nuclear stations (PWR) and other heat exchangers for temperature up to about 550°C (1020°F) where good resistance to stress corrosion cracking (SCC) and intergranul

Sandvik SAF 3207 HD™ is a hyper-duplex (austenitic-ferritic) stainless steel for service in highly corrosive conditions where also high mechanical strength is necessary. This makes the grade ideal for applications such as deepwater umbilicals. Sandvik SAF 3207 HD™ is characterized by: Excellent res

The main property of UGIMA® 4541 is its resistance to intergranular corrosion. It uses titanium as a stabilising element to avoid the formation of chromium carbides in the grade when it is used at high temperature. The mechanical properties of this stainless steel are better than those of 1.4307.

UGIMA® 4509 is an improved machinability ferritic stainless steel containing approximately 18% chromium and stabilised with niobium and titanium. Apart from good corrosion resistance, this grade is characterised by its high suitability for different methods of working, such as machining, cold headi

Aluminum AA 5086 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, AA 5086 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welded with

Aluminum AA 5086 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, AA 5086 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welded with

Aluminum EN AW-5052 is a non-heat treatable alloy with excellent finishing qualities. EN AW-5052 offers better corrosion resistance than most aluminum alloys, especially to salt water and marine atmospheres. This alloy can be readily welded using most common techniques and is in fact offers some of

Aluminum AA 5086 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, AA 5086 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welded with

Naturally hard AlMg alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.69 g/cm³H18EN 573-3, EN 1301Rod, Tube, Wire20.0 °C2.68 g/cm³H18EN 573-3WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus70.0 GP

Naturally hard AlMg alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.69 g/cm³H14EN 573-3, EN 1301Rod, Tube, Wire20.0 °C2.68 g/cm³H14EN 573-3WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus70.0 GP

Naturally hard AlMg alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.69 g/cm³H12EN 573-3, EN 1301Rod, Tube, Wire20.0 °C2.68 g/cm³H12EN 573-3WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus70.0 GP

Aluminum AA 5086 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, AA 5086 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welded with

Aluminum AA 5086 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, AA 5086 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welded with