Pure aluminium This material is well anodically oxidizable, and possesses a good electrical and thermal conductivity. The splinter-giving workability is bad because of danger of smearing. Its mechanical strength is low, the plasticity high. The forming capacity and the chemical as well as the weathe

0.35 mm in accordance to DIN 1745. Application: The main application lies in the building industry. In the building industry for lamella net curtains, rolling shutter, roll gates, in food industry (including table-ware) and for transport containers.PropertiesGeneralPropertyTemperatureValueConditionR

Naturally hard AlFeSi alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H16EN 573-3, EN 485, EN 683Strip, Sheet, Plate, Foil20.0 °C2.71 g/cm³H16EN 573-3Flat, FoilMechanicalPropertyTemperatureValueConditionRelated StandardsShapeComm

Naturally hard AlFeSi alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H14EN 573-3, EN 485, EN 541, EN 683Strip, Sheet, Plate, Foil20.0 °C2.71 g/cm³H14EN 573-3Sheet, Flat, FoilMechanicalPropertyTemperatureValueConditionRelated Sta

Naturally hard AlFeSi alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H26EN 573-3, EN 485, EN 546Strip, Sheet, Plate, Foil20.0 °C2.71 g/cm³H26EN 573-3Foil, FlatMechanicalPropertyTemperatureValueConditionRelated StandardsShapeComm

This cold and hot hardenable material reaches mechanical strength from 200 to 250 MPa with A5-elongation at break of approx. 10 %. In the warm and cold-hardened state this alloy is only limited ductile, in the soft material condition however well. Weldability, corrosion resistance and anodising of

Aluminum DIN 3.1355, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

Aluminum DIN 3.1355, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

The alloy AlCuMg1 belongs to the type of alloy (AlCuMg type), which found of the aluminum wrought machine materials as first in the technology use. Alloys of this type are cold and warm hardenable. They reach thereby high mechanical strength and are relatively heat resistant even in soft condition.

DIN 3.1255 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1255 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.8 g/cm³T451EN 573-3, EN

The alloy AlMn1Mg1 has similar properties like AlMn1, however it reaches higher strength (to F 26). It has also relatively high strength in the soft condition, but it is well cold fomrable. The alloy belongs to the nature-hard aluminum materials. A strength increase can be achieved, not by a purpose

The alloy AlMn1Mg1 has similar properties like AlMn1, however it reaches higher strength (to F 26). It has also relatively high strength in the soft condition, but it is well cold fomrable. The alloy belongs to the nature-hard aluminum materials. A strength increase can be achieved, not by a purpose

The alloy AlMn1Mg0,5 is similarly to AlMn1 in its properties. It reaches strength up to F 25. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occure by cold forming. It is very well hot and cold formable and is suitable to the deep-drawing (no lappet formation).

The alloy AlMn1Mg0,5 is similarly to AlMn1 in its properties. It reaches strength up to F 25. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occure by cold forming. It is very well hot and cold formable and is suitable to the deep-drawing (no lappet formation).

The alloy AlMn1Mg0,5 is similarly to AlMn1 in its properties. It reaches strength up to F 25. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occure by cold forming. It is very well hot and cold formable and is suitable to the deep-drawing (no lappet formation).

Aluminum DIN 3.0517 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, DIN 3.0517 is weldable by conventional welding me

Aluminum DIN 3.0517 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, DIN 3.0517 is weldable by conventional welding me

Food safe aluminum.Quantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process optimisation, quality monitoring, sample analysis, prototyping, trainingBIKAR

Aluminum DIN 3.3545 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, DIN 3.3545 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welde

Aluminum DIN 3.3545 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, DIN 3.3545 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welde