PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C2.7 g/cm³Typical for Wrought 1000 Series AluminiumMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C68 - 70 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes23.0 °C22 - 35 MPa·√mTypical for Wrought 10

PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series AluminiumMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series AluminiumPoisson's r

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C18 - 20 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelSh

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C22 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

Properties: - hardenable corrosion resistant steel - high wear resistance and excellent cutting hardness - corrosion resistance is similar to 13%-Cr-steels, because of its high carbon content - application temperature: up to 200 °C Application: - for cutting tools, like knifes, surgical instruments

Properties: - hardenable steel with high hardness and high wear resistance - resistant to water and steam with fine grounded or polished surface in hardened state - in annealed or high tempered state, corrosion resitance is not sufficient Application: - for cutting tools, like scissors, knife blades

Properties: - hardenable stainless steel - good corrosion resistance to water and steam, is only given for fine grounded and polished surfaces in hardened state, like at other martensitic steels Application: - for cutting toolsPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 - 7.71 g/cm³Me

The fully austenitic material GX2CrNiMoN18-14, with the material number 1.3960 according to SEW 395-98 (the former G-X 2 CrNiMoN 18 14, material number 1.3952 according to SEW 395-87), possesses a defined low value of the relative magnetic permeability of 1.01 maximum (for castings with a wall thick

The fully austenitic material G-X 12 CrNi 18 11 possesses a defined low value of the relative magnetic permeability of 1.01 maximum (for castings with a wall thickness of up to 50 mm). It is applied for construction components which an interference or shielding of a magnetic field must not occur at.

The fully austenitic material G-X 2 CrNiMoN 18 14, with the material number 1.3952 according to SEW 395-87 (invalidly replaced by GX2CrNiMoN18-14, material number 1.3960 according to SEW 395-98), possesses a defined low value of the relative magnetic permeability of 1.01 maximum (for castings with a

The fully austenitic material G-X 120 Mn 13 possesses a defined low value of the relative magnetic permeability of 1.01 maximum (for castings with a wall thickness of up to 50 mm). It is applied for construction components which an interference or shielding of a magnetic field must not occur at. To

Medium Strength GradePropertiesGeneralPropertyTemperatureValueCommentDensity20.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C200 - 215 GPaTypical for Medium Carbon SteelElongation20.0 °C10 %Hardness, HBW20.0 °C207 - 225 [-]Poisson&#x

Medium Strength GradePropertiesGeneralPropertyTemperatureValueCommentDensity20.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C200 - 215 GPaTypical for Medium Carbon SteelElongation20.0 °C16 %Hardness, HBW20.0 °C170 - 229 [-]Poisson&#x

Gold (Au) is a reddish-yellow, in very thin films blue-green translucent, cubic crystallizing precious metal. It is one of the heaviest metals, is relatively soft and very elastic. Among all metals, it has the best hot and cold ductility and can be hammered down to foil up to 0.0001 mm thick. Gold,

Gold (Au) is a reddish-yellow, in very thin films blue-green translucent, cubic crystallizing precious metal. It is one of the heaviest metals, is relatively soft and very elastic. Among all metals, it has the best hot and cold ductility and can be hammered down to foil up to 0.0001 mm thick. Gold,

Gold (Au) is a reddish-yellow, in very thin films blue-green translucent, cubic crystallizing precious metal. It is one of the heaviest metals, is relatively soft and very elastic. Among all metals, it has the best hot and cold ductility and can be hammered down to foil up to 0.0001 mm thick. Gold,

AgCu28, also known as Ag72Cu28 or 72Ag28Cu, is ductile, has good spring properties, is sulfur sensitive, and is non-oxidation resistant. It is machinable, roll-cladable and conditionally separable from the gas phase.Application: AC and DC switches for power and telecommunications at switching curren

AgCu20 material is used as AC and DC switch for power and communications engineering with switching currents up to 10 A, isolated up to 25 A, more rarely at higher currents.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C10.2 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °

AgCu10, also called Ag90Cu10 or 90Ag10Cu, is ductile, sensitive to sulfur and not oxidation resistant. AgCu10 is machinable, roll-cladable and can be separated from the gas phase. The AgCu materials are used as AC and DC switches for power and communications engineering with switching currents up to

Seamless and welded powdermetallurgical tantalum tubes with excellent corrosion resistance.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C16.65 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C186 GPaElongation A2520.0 °C25 %Elongation A5020.0 °C25 %Poisson's ratio20.