Naturally hard AlMn alloy. The alloy is food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.71 g/cm³H44EN 573-3, EN 541Strip, Sheet, PlateMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.5 - 70.0 GPaTypical for Wrought 3000 Series

Naturally hard AlMn alloy. The alloy is food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.71 g/cm³H26EN 573-3, EN 541Strip, Sheet, PlateMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.5 - 70.0 GPaTypical for Wrought 3000 Series

Naturally hard AlMn alloy. The alloy is food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.71 g/cm³H16EN 573-3, EN 541Strip, Sheet, PlateMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.5 - 70.0 GPaTypical for Wrought 3000 Series

Naturally hard AlMn alloy. The alloy is food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.72 g/cm³H19EN 573-3, EN 541Strip, Sheet, PlateMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.5 - 70.0 GPaTypical for Wrought 3000 Series

Aluminum Alloy EN AW-2219, an age-hardenable alloy is produced with a copper additive. It is well-known for its excellent structural strength and it’s used for numerous high temperature applications. It is a suitable alloy for many metalworking processes including machining, forming, heat treatmen

Age-hardenable AlCu alloy. The alloy is not food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.75 g/cm³H18EN 573-3, EN 1301Wire20.0 °C2.74 g/cm³H18EN 573-3WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus70.0 GPaH18EN

Age-hardenable AlCu alloy. The alloy is not food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.8 g/cm³H13EN 573-3, EN 1301Strip, Sheet, Plate, Rod, Welded Tube, Tube, WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus73.0 GPaH13EN

GD-AlSi10Mg is an nearly eutectic alloy with excellent casting properties, good resistance to hot cracking, good machinablity and high chemical resistance. Applicable for complex thin-walled, pressure-tight and fatiguing loaded cast pieces with highest strength after hardening. Application: machine

G-AlSi10Mg is a near eutectic alloy with excellent casting characteristics. It exhibits well plasticity with medium strength. The alloy is suitable for difficult shapes, thin-walled, pressure tight, oscillating loaded, impact loaded cast parts. Application: devices, machines, vehicle and apparatus e

DIN 3.1254 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1254 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyValueCommentDensity2.75 - 2.84 g/cm³Typical for Wrought 2000 Ser

The alloy AlMn1Mg1 has similar properties like AlMn1, however it reaches higher strength (to F 26). It has also relatively high strength in the soft condition, but it is well cold fomrable. The alloy belongs to the nature-hard aluminum materials. A strength increase can be achieved, not by a purpose

DILLIMAX 690 PE is a high strength quenched and tempered, fine grained steel (through sufficient aluminium content) for pressure equipment with a minimum yield strength of 690 MPa in its delivered condition (referring to the lowest thickness range). Its mechanical properties are achieved by water qu

DIFENDER 400 is an alloyed, high strength quenched and tempered steel with a resistance against bullet and fragments impacts and the effects of blast. PropertiesGeneralPropertyValueCarbon equivalent noteTypical values for carbon equivalent (CEV) can be submitted upon request.MechanicalPropertyTemper

DIFENDER 600 is an alloyed, high strength quenched and tempered steel with a resistance against bullet impacts. PropertiesGeneralPropertyValueCarbon equivalent noteTypical values for carbon equivalent (CEV) can be submitted upon request.MechanicalPropertyTemperatureValueTesting StandardCommentCharpy

UNS R52400 has physical and mechanical properties equivalent to CP3 titanium or Grade 2. It has excellent welding and fabrication properties and is extremely resistant to corrosion especially from reducing acids.PropertiesGeneralPropertyValueRelated StandardsShapeDensity4.5 g/cm³ASME SB-363, ASME S

Material EN AW-Al 99,0(A) is produced in limited quantities for sheets, bands and plates as well as for rolled bars. It is food-safe.PropertiesGeneralPropertyValueDensity2.71 g/cm³MechanicalPropertyValueCommentElastic modulus67.0 GPaPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought

2.4375 (NiCu30Al) is a precipitation hardening nickel copper alloy that retains the excellent corrosion resistance of Monel Alloy 400 with the added advantage of increased strength and hardness values that can be maintained up to 650ºC. It is widely used in marine environments due to its excellent c

2.4360 (NiCu30Fe) is a nickel-copper alloy resistant to seawater and steam at high temperatures and widely used in the chemical, oil and marine industries. As a solution strengthened material, Monel Alloy 400 displays good strength, toughness and corrosion resistance at temperatures up to 400°C. It

The steel is used for rail vehicle engineering acc. to the selected standard DIN 5512-1.The corresponding properties of EN 10025-2 shall be taken.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic

DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te