Free cutting steel 11SMn30 is unsuitable for heat-treatment and represents the standard sort for all bulk turned parts, also for parts of complicate full cross-section machining (e.g. spark plugs) and it replaces steel 9SMn28 (DIN 1651 : 1988-04). 11SMn30 is suitable for thin-walled parts and low co

The free cutting case hardening steel 10S20 shows considerably uniformer properties of the cross-section and within the melt than semi-killed free cutting steels. 10S20 shows compared to 15 S 10 (DIN 1651 : 1988-04) a slightly higher machinability at relatively favorable ductility properties. Applic

S255J2G3C is used for folding, cold forming and cold drawing grade. The high-tensile fine grained steel is applicated for welding constructions of dynamic load at temperatures up to -20 °C. Compared to S235J2G3C is achievable a considerable material saving due to its by 120 MPa higher yield point. T

S235JRG2C is used for folding, cold forming and cold drawing grade. The steel is applicable for welding constructions of temperatures up to -20°C depending on load. Max. product thickness accounts 20 mm for folding grades and 8 mm for cold forming grades. As a bright steel product it is used in the

Steel C15 is suitable for parts of slightly higher core strength in vehicle and machine engineering, that are predominantly wear loaded (e.g. levers, joints, nuts, gear wheels). Lowest application temperature -25 °C, most favorable application area 5 to 10 mm nominal size. As a bright steel product

Steel C10 is suitable for parts of low core strength in vehicle and machine engineering, that are predominantly wear loaded (e.g. full dog points, levers, compression moldings and stamped parts). Lowest application temperature -25 °C, most favorable application area 5 to 10 mm nominal size. As a bri

H400LA, mat. No. 1.0556, is a micro alloyed steel with a min. yield strength of 400 N/mm² and a min. ultimate strain of 18 %. The material is well cold formable. The mandrel diameter at bending test 180° amounts to 0,5e for transverse test specimen (e= nominal thickness). Thin sheets made of micro

H360LA, mat. No. 1.0550, is a micro alloyed steel with a min. yield strength of 360 N/mm² and a min. ultimate strain of 20 %. The material is well cold formable. The mandrel diameter at bending test min. 180° amounts to 0,5e for transverse test specimen (e= nominal thickness). Thin sheets made of m

H320LA, mat. No. 1.0548, is a micro alloyed steel with a min. yield strength of 320 N/mm² and a min. ultimate strain of 22 %. The material is well cold formable. The mandrel diameter at bending test min. 180° amounts to 0e for transverse test specimen (e= nominal thickness). Thin sheets made of mic

H280LA, mat. No. 1.0489, is a micro alloyed steel with a min. yield strength of 280 N/mm² and a min. ultimate strain of 24 %. The material is well cold formable. The mandrel diameter at bending test min. 180° amounts to 0e for transverse test specimen (e= nominal thickness). Thin sheets made of mic

Steel C22 is suitable for low strained parts of small heat-treatment sections in vehicle and machine engineering (e.g. piston rods, gear wheels).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C211.35 - 212 GPa10

Steel P285NH is a weldable fine grained steel with a yield strength of max. 285 N/mm². Application: pressure vessel construction, apparatus engineering, general machine and toolbuilding.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanic

The high-temperature steel P305GH, material number 1.0436 is used for pressure vessels.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElon

The high-temperature steel P305GH, material number 1.0436 is used for pressure vessels.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElon

The high-temperature steel P305GH, material number 1.0436 is used for pressure vessels.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElon

The high-temperature steel P280GH, material number 1.0426 is used for pressure vessels.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElon

The high-temperature steel P280GH, material number 1.0426 is used for pressure vessels.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElon

High temperature steel forging for pressure purposes.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C23 - 25 %Poisson'

High temperature steel forging for pressure purposes.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C23 - 25 %Poisson'

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C22 %Elongation A5023.0 °C22 %Poisson's ratio23.0 °C0.29 [-]Typical fo