PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Medium Carbon SteelElongation A5023.0 °C17 %Elongation A8023.0 °C15 %Hardness, Rockwell B23.0 °C78 [-]Ha

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Medium Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Medium Carbon SteelElongation A5023.0 °C18 %Elongation A8023.0 °C16 %Hardness, Rockwell B23.0 °C76 [-]Ha

CuNi10Fe1Mn (CW352H) is comparable to CuNi10Fe1Mn, mat. no. 2.0872, acc. to DIN 17664 : 1983-12. To the comparable DIN-mark applies: The material shows favorable specific strength values also at endurance loading and increased temperatures. Thermal conductivity of pure copper is strongly reduced by

CuNi10Fe1Mn (CW352H) is comparable to CuNi10Fe1Mn, mat. no. 2.0872, acc. to DIN 17664 : 1983-12. To the comparable DIN-mark applies: The material shows favorable specific strength values also at endurance loading and increased temperatures. Thermal conductivity of pure copper is strongly reduced by

Non-alloy steel wire rod for cold drawing for general purpose rodPropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelPoisson's ratio23.0 °

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200

Non-alloy steel wire rod for cold drawing for general purpose rodPropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelPoisson's ratio23.0 °

The aviation material G-TiAl6V4, material number 3.7264, according to the Werkstoffleistungsblatt der Deutschen Luftfahrt WL 3.7264, part 1 and part material G-TiAl6V4, material number 3.7161, according to DIN 17865-90. The material is applied as weight-saving construction material in the aviation.

Castings made from G-Ti3Pd with the material number 3.7052 are preferably applied in the apparatus construction as well as for application purposes with demands on the corrosion-resistance, e.g. in the chemical industry, paper, cellulose, textile and food industry, in the energy extraction and marit

Castings made from G-Ti3 with the material number 3.7051 are preferably applied in the apparatus construction as well as for application purposes with demands on the corrosion-resistance, e.g. in the chemical industry, paper, cellulose, textile and food industry, in the energy extraction and maritim

SAE 1010 is a plain steel steel that has a low carbon content. The properties of SAE 1010 mean that it can be fairly easily machined and formed. The mechanical properties may be improved via heat treatment. Typically not considered a common steel.PropertiesGeneralPropertyValueCommentDensity7.8 - 7.9

SAE 1006 is ideal for deep drawing and resistant to static stress. Its known for its excellent forming performance, processing consistency and high rigidity. Its good formability enables cold forming operationsPropertiesGeneralPropertyValueCommentDensity7.8 - 7.9 g/cm³Typical for Low Carbon SteelMec

7 mm) as well as for helical springs and disc springs (also for mechanical engineering).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.85 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C210 - 212 GPa100.0 °C206 - 207 GPa200.0 °C199 - 200 GPa300.0 °C192 -

The steel 55 Cr 3 is used for hot formed springs like plate springs, torsion springs, helical springs for autmotive engineering as well as for bigger tension or compression springs for special purposes.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 g/cm³MechanicalPropertyTemperatureValu

The steel 54 SiCr 6 is mainly used for hot formed spring wire.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.85 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C210 - 212 GPa100.0 °C206 - 207 GPa200.0 °C199 - 200 GPa300.0 °C192 - 193 GPa400.0 °C184 GPa500

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200

Non-alloy steel wire rod for drawing and/or cold rolling for general purpose wire rod (e.g. application for springs, steel wire).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200