ASTM 7075 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero tem

ASTM 7050 is a heat treatable alloy that has very high mechanical properties and high fracture toughness. Popular with the aerospace industry, ASTM 7050 offers good stress and corrosion cracking resistance and high strength at subzero temperatures.PropertiesGeneralPropertyValueCommentDensity2.7 - 2.

ASTM 7050 is a heat treatable alloy that has very high mechanical properties and high fracture toughness. Popular with the aerospace industry, ASTM 7050 offers good stress and corrosion cracking resistance and high strength at subzero temperatures.PropertiesGeneralPropertyValueCommentDensity2.7 - 2.

ASTM 6061 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.Quantity: 1 PCSPropertiesGeneralPropertyValueComment

ASTM 6061 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.Quantity: 1 PCSPropertiesGeneralPropertyValueComment

Aluminum ASTM 3003 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, ASTM 3003 is weldable by conventional welding meth

The structural steel (non-alloy high-grade steel) S550GD is deliverable with following hot-dip coatings: S550GD+Z (coating Zn), S550GD+ZF (coating Zn-Fe), S550GD+ZA (coating Zn-Al), S550GD+AZ (coating Al-Zn). The coating mass for Z amounts to 100, 140, 200, (225), 275, 350*, (450)* and (600)* g/m²,

The alloyed high-grade steel DX51D (machine folding quality) is deliverable with following hot-dip coatings: DX51D+Z (coating Zn), DX51D+ZF (coating Zn-Fe), DX51D+ZA (coating Zn-Al), DX51D+AZ (coating Al-Zn), DX51D+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275, 350

Cryogenic Ni-alloy steel for pressure vessel construction, refrigerators, transmission parts and for construction parts in machine and apparatus engineering up to -196 °C.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity20 °C7.88 g/cm³normalized or quenched and tempered

The steel C125S is used as cold rolled strip for springs and special applications in thicknesses of up to 6 mm and as tempered cold strip in thicknesses from 0.30 to 3.00 mm. The springs made of steel C125S are suitable for highly stressed tension springs, especially in the watch industry, as well a

The steel C125S is used as cold rolled strip for springs and special applications in thicknesses of up to 6 mm and as tempered cold strip in thicknesses from 0.30 to 3.00 mm. The springs made of steel C125S are suitable for highly stressed tension springs, especially in the watch industry, as well a

Seamless precision steel tube made from St 30 Si is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Si is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Si is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Al is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Al is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Al is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

The balanced high performance machining steel 9 SMnPb 36 shows an excellent cutting behaviour. Because of the S content a lower toughness and a increased crack danger. Application: mass components in the automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureV

The balanced machining steel 9 SMnPb 28 is used for higher demands on the cutting capacity and surface condition. The steel shows a lower crack sensitivity. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³Mechan

The balanced machining steel 9 SMn 36 is used for higher demands on the cutting capacity and surface condition. The steel shows a elevated crack sensitivity. Application: limited in the automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C