Free cutting steel 11SMnPb37 is a very-high-performance free cutting steel of excellent machining properties. It is unsuitable for heat-treatment. Deteriorating ductility qualities due to increased S-content and higher cracking risk have to be considered. 11SMnPb37 shows compared to 11SMn37 better p

Free cutting steel 11SMnPb30 is unsuitable for heat-treatment and is preferred steel 11SMn30 for higher requirements to machinability and surface appearance. 11SMnPb30 shows a lower cracking sensitivity compared to steel with a higher S-content (11SMn37, 11SMnPb37). Application for bulk parts in car

Initial material for E-Al according to DIN 1712-3PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series AluminiumMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical

Naturally hard AlMg alloy. The alloy is food safe.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.67 g/cm³EN 573-3WireMechanicalPropertyValueCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought

Age-hardenable AlCu alloy. The alloy is not food safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.8 g/cm³H18EN 573-3, EN 1301Strip, Sheet, Plate, Rod, Welded Tube, Tube, WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus73.0 GPaH18EN

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.705 g/cm³EN 573-3WireMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series AluminiumPoisson&#

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.705 g/cm³EN 573-3FoilMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series AluminiumPoisson&#

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.71 g/cm³EN 573-3Strip, Sheet, PlateMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series Alum

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.7 g/cm³EN 573-3Strip, Sheet, Plate, FoilMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.7 g/cm³EN 573-3Strip, Sheet, PlateMechanicalPropertyValueCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 1000 Series Alumi

Food safe aluminum.PropertiesGeneralPropertyValueRelated StandardsShapeDensity2.705 g/cm³EN 573-3Strip, Sheet, Plate, Tube, BarMechanicalPropertyValueRelated StandardsShapeCommentElastic modulus69.0 GPaEN 573-3Strip, Sheet, Plate, Tube, BarPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.65 g/cm³T5EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsCommentElastic modulus20.0 °C74.0 GPaT5EN 1706Elongation-196.0 °C0.6 %T5EN 17

The alloy G-AlMg3Si solidified in a wide temperature range, is sufficiently castable and poses excellent weather and corrosion resistance. G-AlMg3Si is especially applicable for mechanically high loaded cast pieces. It is excellent polishable and able for anodic oxdising for decorative purpose. Appl

G-AlSi12 is an eutectic alloy with excellent casting characteristics. It has a medium strength but good plasticity, is weather and corrosion resistant. The alloy is suitable for difficult shapes, thin-walled, impact loaded cast parts. Application: devices, machines, vehicle, ship and apparatus engin

G-AlSi11 - eutectic alloy - excellent ability for filling shapes and casting properties with high chemical resistance - high hot crack resistance - applicable for complex, thin walled, pressure tight and stable at vibration cast pieces with good corrosion resistance application: - parts of machines,

Niclafor® 1000 is a range of Copper-Nickel-Tin (CuNi9Sn6) alloys designed and produced by Lebronze alloys (ex. CLAL). Mechanical advantages: Niclafor® 1000 exhibits very high mechanical properties, such as Tensile Strength and Yield Strength above 1,000 MPa (145 ksi) depending on temper, even at h

Niclafor® 1000 is a range of Copper-Nickel-Tin (CuNi9Sn6) alloys designed and produced by Lebronze alloys (ex. CLAL). Mechanical advantages: Niclafor® 1000 exhibits very high mechanical properties, such as Tensile Strength and Yield Strength above 1,000 MPa (145 ksi) depending on temper, even at h

Precision rolled plate UNIDAL® made from alloy EN AW 7019 (AlZn4Mg2), finely milled on both sides and covered with protective film, is characterized by a narrow tolerance of flatness and thickness and has only relatively low residual stresses. The good anodizing and welding capability opens up a wid

Steel for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon SteelPropertiesGeneralPropertyValueCommentDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyValueCommentElastic modulus200 - 215 GPatypical for low carbon steelElongation20 - 22 %min. values depending on the t

Steel for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese- Silicon SteelPropertiesGeneralPropertyValueCommentDensity7.8 - 7.9 g/cm³typical for low carbon steelMechanicalPropertyValueCommentElastic modulus200 - 215 GPatypical for low carbon steelElongation20 - 22 %min. values depending on the