Balanced machining steel 9 SMn 28 is the standard grade for all mass turning tools and should be the substitution of the 9 S 20. The steel is suited for thin walled parts and little cold forming. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTempera

The fully killed machining steel 15 S 10 is applicated in the case hardened condition for thin walled parts with higher toughness demands. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemper

The free cutting case hardening steel 10SPb020 shows uniform properties of the cross-section and within the melt as well as enhanced machinability by Pb- and S-addition. Application for thin-walled case hardened parts in car industry, apparatus, equipment and machine engineering. As a bright steel p

As a bright steel product it is used in the form of bars, bright, straight, in various conditions (see DIN EN 10277 : 1999-10).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 -

The stainless steel X5CrNiMo17-12-2 is usually used cold drawn as wire up to 10 mm diameter for springs or spring parts. It is highest corrosion resistant and applicable up to 250 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.96 g/cm³22.0 °C7.96 g/cm³MechanicalPropertyTemperatureValueE

The stainless steel X10CrNi18-8 is usually used cold drawn as wire up to 10 mm diameter for springs or spring parts. It is resistant to corrosion and applicable up to 250°C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.92 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C206

The round, oil hardened and tempered carbon steel wire VDC with high fatigue strength and low tensile strength is used mainly for torsion loaded springs (tension and compression springs) mostly at room temperature. It will be delivered in rings, in coils or as bars and, if not otherwise arranged, th

The round, oil hardened and tempered carbon steel wire TDC with medium fatigue strength and low tensile strength is used mainly for torsion loaded springs (tension and compression springs). It will be delivered in rings, in coils or as bars and, if not otherwise arranged, thin oiled.PropertiesGenera

The round, oil hardened and tempered carbon steel wire FDC for static loading and low tensile strength is used mainly for torsion loaded springs (tension and compression springs). It will be delivered in rings, in coils or as bars and, if not otherwise arranged, thin oiled.PropertiesGeneralPropertyT

The patented cold drawn steel wire type SM (S-static load M-medium tensile strength) made of unalloyed steel is used for tension springs, compression springs or torsion springs for medium static load or rare dynamic load. The wire will be delivered in rings (standard delivery type), coils or levell

The patented cold drawn steel wire type SL (S-static load L-low tensile strength) made of unalloyed steel is used for tension springs, compression springs or torsion springs for mostly low static load. The wire will be delivered in rings (standard delivery type), coils or levelled bars. Different s

S355J2G3 is a high-tensile fine grain steel for welding constructions of dynamic load. Compared to S235J2G3 is achievable a considerable saving of material due to the by 120 MPa higher yield point. The steel shows a by 15% higher resistance to wear due to sliding action compared to S235J2G3.Properti

S235JRG2 is applicable for welding constructions.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °C184 GPa500.0 °C175 GPa600.0 °C164 GPaPoisson&#x

S235J2G3 is a fine grain steel for welding constructions of dynamic load.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °C184 GPa500.0 °C175 GPa6

The free-cutting steel 15SMn13, suitable for case-hardening, is used for production of turned parts.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Car

Free-cutting steel 11SMnPb37 is not intended for heat-treatment and is one of the maximum demand free cutting steels due to its excellent machinability properties. Reduced ductility properties and increased cracking risk due to the higher S-content have to be considered. 11SMnPb37 shows compared to

Free-cutting steel 11SMnPb30 is not intended for heat-treatment and is preferred 11SMnPb30 for higher machinability and surface appearance demands. Steel 11SMnPb30 shows lower crack sensitivity compared to higher S-containing steels (11SMn37, 11SMnPb37). Application for bulk parts in car industry as

Free-cutting steel 10SPb20, suitable for case-hardening, has permanent properties of the cross-section and within the melt as well as enhanced machinability by Pb and S-addition. Application for thin-walled, case-hardened parts in car industry, in apparatus, equipment and machine engineering.Propert

Steel C25 is suitable for low strained parts of small heat-treatment sections in vehicle manufacturing and machine engineering (e.g. gear wheels, piston rods). Lowest working temperature -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.85 g/cm³MechanicalPropertyTemperatureValue

Steel C22 is suitable for slightly loaded parts of small heat-treatment sections in vehicle manufacturing and machine engineering (e.g. piston rods, gear wheels). Lowest working temperature -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.85 g/cm³MechanicalPropertyTemperatureVa