Titanium UNS R56400 alloy is the most commercially available of all titanium alloys. It offers an excellent combination of high strength and toughness. UNS R56400 titanium has good welding and fabrication characteristics.PropertiesGeneralPropertyValueRelated StandardsShapeDensity4.43 g/cm³AM­S 49­28

SILVERSPEED-XL is a copper alloy with additions of zinc and nickel to give an attractive soft silvery colour not as brash as stainless steel. It is a truly superlative free-machining alloy with a machinability rating almost the same as free cutting brass. It is highly recommended for the production

C17510 TH04, contains around 2% nickel and features good mechanical properties, high electrical conductivity and very good machinability. As a result, it has moderate strength and finds application in current-carrying springs, thermal control devices, welding electrodes and power connectors.Properti

C17200 (CuBe2) TD04, also known as CuBe2, is the most commonly specified beryllium copper and offers a wide combination of properties including good electrical conductivity, good formability and very high electrical and mechanical properties after heat treatment. This grade is supplied in age harden

C17200 (CuBe2) is the most commonly specified beryllium copper and offers a wide combination of properties including good electrical conductivity, good formability and very high electrical and mechanical properties after heat treatment. This grade is supplied in age hardenable tempers TB00 (A). Thes

DTD498 (CuNi2Si) is a copper-nickel-silicon alloy which demonstrates a combination of high mechanical strength and notch ductility whilst still possessing superior electrical and thermal conductivities. It shows the following features and properties: Good electrical and thermal conductivity Low mag

The steel is used for the manufacture of bolts, nuts and rivets (and similar shaped parts).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon Steel

The steel is used for the manufacture of bolts, nuts and rivets (and similar shaped parts).PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon Steel

The steel Cm 15 is used for wear loaded parts with higher core strength in the vehicle and mechanical engineering (e.g. levers, joints, gears). Because of the S-content the steel has a better machinability. The lowest application amounts to -25 °C, the best application from 5 to 10 mm nominal size.P

Steel C15R is suitable for parts of slightly higher core strength in vehicle manufacturing and machine engineering, which are predominantly wear loaded (e.g. levers, joints, gear wheels).The steel has an enhanced workability due to its controlled S-content.PropertiesGeneralPropertyTemperatureValueDe

The patented cold drawn steel wire type A made of unalloyed steel is used for coil springs (tension springs, compression springs, torsion springs), spring rings and other springs for low static load or rare dynamic load.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typ

G-CuNi10 possesses very good corrosion resistance to all kinds of water, like drinking water, river waters, brackish water, mining water, sea water, acids and ammoniac condensers as well as not-oxidizing diluted acids, alkaline solutions and salt solutions, organic acids and dry gases, like oxygen,

Reinforcing steel is used for the reinforcement of concrete. The steel B500B is a steel of the ductility class B.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypica

Reinforcing steel is used for the reinforcement of concrete. The steel B500A is a steel of the ductility class A.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypica

G-CuNi30 possesses a very good corrosion resistance to all kinds of water, like drinking water, river waters, brackish water, mining water, sea water, sour and ammonic condensates as well as not-oxidizing acids, alkaline solutions and salt solutions, organic acids and dry gases, like oxygen, chlorin

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation A5023.0 °C11 %Hardness, Rockwell B23.0 °C75 [-]Hardness, Rockwell C23.0 °C20 [-]

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation A5023.0 °C11 %Hardness, Rockwell B23.0 °C78 [-]Hardness, Rockwell C23.0 °C20 [-]

PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C95 - 98 GPaTypical for Wrought Copper Pure / Low Alloyed CopperElongation23.0 °C33 %Hardness, Vickers23.0 °C55 [-]Poisson's ratio23.0 °C0.34 [-]Typical for Wrought Copp

Quantity: Depending on material – Contact usAdditional services: Specific treatments, size customisation, co-designBIKAR-METALLE GMBHMANUFACTURER AND DISTRIBUTORInformation and servicesAdditional services: Cuttings, Parts from drawings PropertiesGeneralPropertyTemperatureValueDensity23.0 °C8.4 g/cm³

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.78 g/cm³T53AA Standards, ASTM B221MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus69.0 - 72.0 GPaTypical for Wrought 7000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 7000 S