Alloy 25 rod and bar from Materion Performance Alloys provide the highest strength of any copper alloy, with electrical and thermal conductivity considerably greater than other high strength copper alloys. This alloy features high fatigue strength and resistance to wear, corrosion, galling, and stre

DI-MC 690 is a high strength thermomechanically rolled, fine grained structural steel with a minimum yield strength of 690 MPa in its delivery condition ex works. DI-MC 690 is preferentially used by the customers for welded steel structures within hydraulic steelworks such as penstocks. PropertiesGe

DI-MC 690 is a high strength thermomechanically rolled, fine grained structural steel with a minimum yield strength of 690 MPa in its delivery condition ex works. DI-MC 690 is preferentially used by the customers for welded steel structures within hydraulic steelworks such as penstocks. PropertiesGe

DILLIDUR IMPACT is a wear resistant steel with a nominal hardness of 340 HBW in delivery condition. DILLIDUR IMPACT is not a constructional steel CE-certified according to EN 10025. DILLIDUR IMPACT is applied where high resistance to abrasion is required together with high toughness and crack resist

DILLIMAX 965 is a high strength quenched and tempered, fine grained structural steel (through sufficient aluminium content.) with a minimum yield strength of 960 MPa (140 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

Properties: - corrosion characteristics can be compared with those of 1.4541 - bends with certain welding conditions tohot cracking - due to the Nb-content not high polishable - for construction of pressure vessels to 300 °C certified, with appraisals to 550 °C Application: - in large extent applica

Properties: - high resistance to pitting corrosion and intergranular corrosion (better than 1.4436) - resistant to crack corrosion, with highest general resistance to many organic acids of high concentration and temperature, e.g. in not oxidizing acids and chloride containing media (sea water), also

6 mm resistant to intergranular corrosion - due to the Ti-additive the steel is not high polishable - is certified for the construction of pressure tanks to 300 °C, if no disintegration of grains-releasing media are present, then up to 550°C is possible - the strength grades E 225, E 355 are usual.

Properties: - full austenitic high polishable steel - higher strength, because of its nitrogen additives, by stronger molybdenum additive higher corrosion resistance than 1.4406, particularly to not-oxidising acids and halogen containing media - higher stability to selective attack than 1.4435 - exc

Properties: - austenitic CrNiMo-steel with increased resistant to not-oxidizing acids and halogen containing media - high polishable, able for well cold forming Application: - for acid-proof apparatuses of the chemical and pharmaceutical industry - for cellulose, rubber, pigment, fatty acid , textil

Properties - austenitic CrNi-steel - because of addition of nitrogen gets higher yield strength, which is resistant to higher temperature, used in pressure tank construction and light constructions - N-content lets increase the corrosion resistance - good able for cold forming - high polishable Appl

Properties: - modification of 1.4301 - higher resistance to intergranular corrosion, caused of its lowered carbon content - application in chemical instrument construction and pharmacy industry - especially at demands for big wall thickness und simultaneous ability to polish to high gloss Applicatio

Properties: - austenitic CrNiMo-steel with increased resistant to not-oxidizing acids and halogen containing media - high polishable, able for well cold forming Application: - for acid-proof apparatuses of the chemical and pharmaceutical industry - for cellulose, rubber, pigment, fatty acid , textil

Properties: - with Ti stabilised variant of 1.4401 - due to the high Mo-content corrosion resistance increased, in particular to not-oxidizing acids and halogen containing media - due to the titanium content the steel possesses a increased resistance to intergranular corrosion - is not high polishab

Properties: - corrosion characteristics can be compared with those of 1.4541 - bends with certain welding conditions tohot cracking - due to the Nb-content not high polishable - for construction of pressure vessels to 300 °C certified, with appraisals to 550 °C Application: - in large extent applica

Properties: - standard type of austenitic CrNi-steels with high corrosion resistance - good workability, very good able for cold forming - application temperature: -200 to 550°C Application: - for welded components of constructions in chemical industry, food industry, housewares, breweries, architec

Material X2CrNiMoN17-11-2 is comparable to trademark X 2 CrNiMoN 17 12 2 acc. to DIN 17440 : 1985-07. This material is a fully austenitic steel which shows higher strength and structure stability owing to nitrogen addition. It has high resistance in oxidizing media. Increased pitting index owing to

Material X2CrNiMo18-15-4 is comparable to X 2 CrNiMo 18 16 4 acc. to DIN 17440 : 1985-07. The steel shows due to its high molybdenum content (above 3 per cent) very good resistance to non oxidizing and halogenated media. It is resistant to intercrystalline corrosion also in sensitized condition. Thi

high-temperature resistant nickel alloyfor sheet metals, volumes, bars, forgings- high-temperature resistant- corrosion resistant- hardenable- weldable - cold-toughApplication- for construction units to 700°C high-temperature resistant and to 980°C to be resistant to scaling (turbine disks, housings

The patented process gives AMPCO® M4 mechanical properties beyond the range of commercial nickel-aluminium bronzes, comparable to beryllium copper at a lower cost and without the beryllium copper industrial hygiene requirements.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C7.45 g/cm³Recycle