DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

DIN 3.4365 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

The alloy AlZnMgCu0,5 belongs to the aluminum materials, which achieve very high mechanical strength. With hot ageing the strength grade F 49 is attainable. This alloy is good splinter-giving machinably. The alloy is weldable with consideration of certain conditions, especially a heat influence zone

Aluminum DIN 3.3545 is structural alloy, which offers users strong corrosion resistance and high electrical conductivity. Offering higher strength levels than 5052 or 5083, DIN 3.3545 becomes stronger with stain hardening and cold working, all while remaining a cost-effective choice. It can be welde

0.35 mm in accordance to DIN 1745. Application: The main application lies in the building industry. In the building industry for lamella net curtains, rolling shutter, roll gates, in food industry (including table-ware) and for transport containers.PropertiesGeneralPropertyTemperatureValueConditionR

The AlMg alloy is characterised all by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increase the strength, the cold forming capacity decreases with it. The alloys of this type are nature hard, i.e. only by a cold forming and not by a purposef

The AlMg alloy is characterised all by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increase the strength, the cold forming capacity decreases with it. The alloys of this type are nature hard, i.e. only by a cold forming and not by a purposef

The AlMg alloy is characterised all by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increase the strength, the cold forming capacity decreases with it. The alloys of this type are nature hard, i.e. only by a cold forming and not by a purposef

The AlMg alloy is characterised all by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increase the strength, the cold forming capacity decreases with it. The alloys of this type are nature hard, i.e. only by a cold forming and not by a purposef

DIN 3.3211 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.PropertiesGeneralPropertyValueCommentDensity2.7 g/c

DIN 3.3211 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.PropertiesGeneralPropertyValueConditionRelated Stan

DIN 3.3211 is a readily available alloy that has good surface finish and ability to be anodized.Easy of weldability and brazability with nice surface finish. Resistance to corrosion from seawater and atmospheric conditions. Suitable for hot forging.PropertiesGeneralPropertyValueConditionRelated Stan

Age-hardenable AlCu alloy. The alloy is not food safe.Additional services: Cuttings, Parts from drawings PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.85 g/cm³T351EN 573-3, EN 754Rod, Tube20.0 °C2.85 g/cm³T351EN 573-3RodMechanicalPropertyTemperatureValueConditionRe

Age-hardenable AlCu alloy. The alloy is not food safe.Additional services: Cuttings, Parts from drawings PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.85 g/cm³T3EN 573-3, EN 754Rod, Tube20.0 °C2.85 g/cm³T3EN 573-3Rod, TubeMechanicalPropertyTemperatureValueCondition

Food safe aluminum.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H42EN 573-3, EN 1396Strip, Sheet, Plate, Foil, Bar, Rod, Tube20.0 °C2.71 g/cm³H42EN 573-3Sheet, Strip20.0 °C2.71 - 2.72 g/cm³H42EN 573-3Sheet, Strip20.0 °C2.72 g/cm³H42EN 573-3Sheet, StripMech

Food safe aluminum.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H46EN 573-3, EN 1396Strip, Sheet, Plate, Foil, Bar, Rod, Tube20.0 °C2.71 g/cm³H46EN 573-3Sheet, Strip20.0 °C2.71 - 2.72 g/cm³H46EN 573-3Sheet, Strip20.0 °C2.72 g/cm³H46EN 573-3Sheet, StripMech

EN AW-1100 is a soft, non-heat-treatable and low strength alloy that offers strong corrosion resistance. Composed of 99% aluminum and 0.12% copper, EN AW-1100 is purest grade of aluminum alloy available commercially.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.71 g/cm³OEN 57