EN AW-7075 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero te

Naturally hard AlFeSi alloy. The alloy is food safe.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.71 g/cm³H111EN 573-3, EN 485Strip, Sheet, Plate, Foil20.0 °C2.71 g/cm³H111EN 573-3FlatMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic m

Age-hardenable AlZn alloy. The alloy is not food safe.Additional services: Cuttings, Parts from drawings PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.78 g/cm³T6510EN 573-3, EN 755Strip, Sheet, Plate, Rod, Tube20.0 °C2.78 g/cm³T6510EN 573-3Profile, Rod, TubeMechani

AA 7075 is a high-strength alloy that offers good stress-corrosion cracking resistance. Known as a mainstay in the aerospace industry since it was introduced, Aluminum 7075 brings moderate toughness as well as an excellent strength-to-weight ratio. It is also important to note that at sub-zero tempe

Aluminum EN AW-6063 is an architectural alloy that offers users a high resistance to corrosion and excellent finishing characteristics. Easy to extrude with fair machinability, EN AW-6063 can be both hot and cold formed and is commonly available as T6 temper as well as T4 temper.PropertiesGeneralPro

Aluminum AA 6063 is an architectural alloy that offers users a high resistance to corrosion and excellent finishing characteristics. Easy to extrude with fair machinability, AA 6063 can be both hot and cold formed and is commonly available as T6 temper as well as T4 temper.PropertiesGeneralPropertyV

This cold and hot hardenable material reaches mechanical strength from 200 to 250 MPa with A5-elongation at break of approx. 10 %. In the warm and cold-hardened state this alloy is only limited ductile, in the soft material condition however well. Weldability, corrosion resistance and anodising of

This cold and hot hardenable material reaches mechanical strength from 200 to 250 MPa with A5-elongation at break of approx. 10 %. In the warm and cold-hardened state this alloy is only limited ductile, in the soft material condition however well. Weldability, corrosion resistance and anodising of

G-AlSi10Mg is a near eutectic alloy with excellent casting characteristics. It exhibits well plasticity with medium strength. The alloy is suitable for difficult shapes, thin-walled, pressure tight, oscillating loaded, impact loaded cast parts. Application: devices, machines, vehicle and apparatus e

G-AlSi9Cu3 is universally used alloy with very good casting characteristics. It is characterised by less inclination to breaking in and to cavities and is mostly not hardened. The alloy is suitable for difficult shapes, thin-walled, pressure tight, oscillating loaded, impact loaded cast parts. Appli

Aluminum DIN 3.1355, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

DIN 3.1255 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1255 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.8 g/cm³T651EN 573-3, EN

DIN 3.1255 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1255 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.8 g/cm³T

DIN 3.1254 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1254 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyValueCommentDensity2.75 - 2.84 g/cm³Typical for Wrought 2000 Ser

The alloy AlMn1Mg0,5 is similarly to AlMn1 in its properties. It reaches strength up to F 25. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occure by cold forming. It is very well hot and cold formable and is suitable to the deep-drawing (no lappet formation).

Aluminum DIN 3.0517 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, DIN 3.0517 is weldable by conventional welding me

The alloy AlMn1 is an Al-Mn alloy, which belongs to the nature-hard aluminum materials. Mn increases the strength compared with pure aluminium, but it does not impair the corrosion resistance. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occur by cold forming

Pure aluminium This material is well anodically oxidizable, and possesses a good electrical and thermal conductivity. The splinter-giving workability is bad because of danger of smearing. Its mechanical strength is low, the plasticity high. The forming capacity and the chemical as well as the weathe

Pure aluminium Electrical conductivity alloy according to DIN, ensured by the German electrotechnical commission for electro-technology with, also in accordance to DIN 40 501 part of 1 to part of 4. This material has a very good electrical and good thermal conductivity, however only relatively low m

AA 6262 is a free-machining alloy that offers users outstanding mechanical strength and good resistance to corrosion. Aluminum AA 6262 is heat treatable and due to the addition of bismuth is easily machinable. Anodizing raises the levels of corrosion resistance and with high-speed tooling you can ac