CTF25E: for the production of PCD tools and tool shanks. The increased cobalt content and the coarser grain improve brazability while increasing fracture toughness.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C14.15 g/cm³Grain structureFine (0,8µm - 1,3µm)MechanicalPropertyTemperatureValueC

Tungsten hard material for wear protectionPropertiesGeneralPropertyTemperatureValueDensity23.0 °C14.45 g/cm³BinderCobalt binderGrain structureSubmicron grain sizeMechanicalPropertyTemperatureValueCompressive strength23.0 °C6600 MPaElastic modulus23.0 °C580 GPaHardness, Rockwell A23.0 °C92.3 [-]Hardn

The binder phase of Ferro-Titanit® U is roughly equivalent to the austenitic CrNiMo steel X 10CrNiMoNb 18 10 (Mat. No. 1.4580). Its high titanium carbide content of 34 % by weight, or 45 % by volume, provides it with outstanding wear resistance. The Cr and Ni contents simultaneously give the materia

BP11NPA is a red colored composite made from a 24 oz/sq. yd canvas which is passed through the treater twice to insure impregnation of the fibers and to obtain the resin content desired for optimal performance. The resin system is a phenolic with good impregnation qualities and cured hardness.Proper

Canvas phenolic laminate with molybdenum disulfide lubricant. The mechanical properties are slightly lower than BP11NPN. BP13NPM is used for lubricity in the composite when carbon (graphite) cannot be used because of conductivity.PropertiesGeneralPropertyValueTesting StandardCommentBonding strength8

Linen phenolic laminate with graphite added as a solid lubricant. The linen substrate provides better surface to machined parts, and, more uniform wear resistance than NP315.PropertiesGeneralPropertyValueTesting StandardCommentBonding strength861.8 KgASTM D229Condition ADensity1.39 g/cm³ASTM D792Moi

Bleached canvas phenolic laminate with graphite added as a solid lubricant. This material has improved wear properties under certain conditions. Better moisture absorption and machinability than NP315. Material is conductive to electricity and should not be used where this is detrimental to the appl

Canvas phenolic laminate with graphite added as a solid lubricant. This material has improved wear properties under certain conditions. Material is conductive to electricity and should not be used where this is detrimental to the application.PropertiesGeneralPropertyValueTesting StandardCommentBondi

Canvas phenolic laminate with molybdenum disulphide added as a solid lubricant. This material has improved wear properties under certain conditions. Material is semi-conductive to electricity and should no be used where this is detrimental to the application.PropertiesGeneralPropertyValueTesting Sta

Canvas phenolic laminate with molybdenum disulfide lubricant. The mechanical properties are slightly lower than NP310. NP313 is used for lubricity in the composite when carbon (graphite) cannot be used because of conductivity.PropertiesGeneralPropertyValueTesting StandardCommentBonding strength861.8

BR70 is a red colored composite made from a 24 oz/sq. yd canvas which is passed through the treater twice to insure impregnation of the fibers and to obtain the resin content desired for optimal performance. The resin system is a phenolic with good impregnation qualities and cured hardness.Propertie

Being a hot oil treated version of RT630, RT630S is a fine machining grade with excellent electrical properties and moisture resistance. It has good dimensional stability and resists splitting.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.28 g/cm³ASTM D792Moisture absorption0.7 %ASTM

Being a heat treated version of RT630, RT630H is a fine machining grade with excellent electrical properties and moisture resistance. It has good dimensional stability and resists splitting.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.33 g/cm³ASTM D792Moisture absorption0.7 %ASTM D5

Grade RTB326 is a tube made from a fine cotton fabric and an epoxy resin system. It has low moisture absorption and excellent dimensional stability and chemical resistance. RTB326 meets ASTM F3131 Type FB.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.33 g/cm³ASTM D792Moisture absorpt

RT509F has good electrical properties under humid conditions and excellent arc resistance. The “F” version is made from a fine weave fabric. RT509F also complies with MIL-I-24768/1, Type GME and ASTM D709 Type IV Grade G-9 and IEC 61212-3-1-MFGC 21.PropertiesGeneralPropertyValueTesting StandardComme

Grade RT509 has good electrical properties under humid conditions and excellent arc resistance. RT509 also complies with MIL-I-24768/1, Type GME and ASTM D709 Type IV Grade G-9 and IEC 61212-3-1-MFGC 21.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.95 g/cm³ASTM D792Moisture absorptio

RT571 is similar to RT511 using a heavy weave glass fabric substrate meeting all of the requirements of NEMA G-10. Like RT511, RT571 has excellent strength at elevated temperatures but has been formulated to facilitate the production of thick walled tubes (up to 4 times thicker than RT511). RT571 al

Grade RT130 meets all of the property requirements of NEMA G-10, with the added feature being flame resistant, UL94 V-0. RT130 also complies with IEC 61212-3-1 EP GC 23, with Excellent machining.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.84 g/cm³ASTM D792Moisture absorption0.1 %AS

Being a heat treated version of RTB320, RTB320H has low moisture absorption and excellent dimensional stability. RTB320H also complies with MIL-I-24768/13, Type FBE, ASTM D709 Type II Grade LE and with IEC 61212-3-1 PF CC 21.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.31 g/cm³ASTM

Grade RTB320 has low moisture absorption and excellent dimensional stability. RTB320 also complies with MIL-I-24768/13, Type FBE, ASTM D709 Type II Grade LE and with IEC 61212-3-1 PF CC 21.PropertiesGeneralPropertyValueTesting StandardCommentDensity1.33 g/cm³ASTM D792Moisture absorption1.15 %ASTM D5