DI-MC 355 is a thermomechanically rolled, fine grained structural steel with minimum yield strength of 355 MPa in its delivery condition ex works (referring to the lowest thickness range). It fulfils the requirements of EN 10025-4. Due to its chemical composition, this material has a low carbon equi

DI-MC 355 is a thermomechanically rolled, fine grained structural steel with minimum yield strength of 355 MPa in its delivery condition ex works (referring to the lowest thickness range). It fulfils the requirements of EN 10025-4. Due to its chemical composition, this material has a low carbon equi

DILLIMAX 690 is a high strength quenched and tempered, fine grained structural (through sufficient aluminium content.) steel with a minimum yield strength of 690 MPa (100 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

DILLIMAX 690 is a high strength quenched and tempered, fine grained structural (through sufficient aluminium content.) steel with a minimum yield strength of 690 MPa (100 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

DILLIMAX 690 is a high strength quenched and tempered, fine grained structural (through sufficient aluminium content.) steel with a minimum yield strength of 690 MPa (100 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

DILLIMAX 965 is a high strength quenched and tempered, fine grained structural steel (through sufficient aluminium content.) with a minimum yield strength of 960 MPa (140 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

DILLIMAX 965 is a high strength quenched and tempered, fine grained structural steel (through sufficient aluminium content.) with a minimum yield strength of 960 MPa (140 ksi) in its delivery condition (referring to the lowest thickness range).PropertiesGeneralPropertyValueCommentCarbon equivalent (

PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.73 g/cm³H14BS EN 573-3, BS EN 485-2Sheet2.8 g/cm³H14MechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus69.5 GPaH14BS EN 573-3, BS EN 485-2Sheet72.0 GPaH14Elongation4.6 %H14Hardness, Brinell45.0 [-]H14BS

Sandvik 3R64 is an austenitic stainless steel with a high molybdenum content. The grade is characterized by improved resistance to general and pitting corrosion in comparison with ASTM 316L. More technical information and charts that are relevant to the materials corrosion, mechanical and physical

Sanicro® 70 is an austenitic nickel-chromium-iron (NiCrFe) alloy characterized by very good resistance to carburization and nitrogen absorption and good structural stability at high temperatures. It also has good resistance to stress corrosion cracking (SCC). More technical information and charts t

NS104 (CuNi12Zn24) is the standard grade of nickel silver for general purpose applications. Primarily a sheet grade, NS 104 contains 12% nickel and is utilised where the additional strength of half hard temper material imparts rigidity and spring properties. The presence of nickel provides corrosion

NS101 (CuNi10Zn42Pb2) is the general purpose grade of nickel silver most commonly used for hot stamping to complex shapes and as machining rod for a wide variety of electrical and electronic components. It has good corrosion and tarnish resistance and is frequently specified for many architectural a

2.0857 (CuNi3Si) ultimate super strength copper nickel silicon alloy, specially developed to provide a unique blend of mechnical and physical properties for high performance engineering. It has similar characteristics to Colsibro®, although Trojan is produced with increased levels of nickel and sili

This aluminium silicon bronze has similar attributes to the other aluminium bronzes, with a 2% silicon addition to enhance the material strength, corrosion resistance and impact strength whilst also improving the alloy machinability. As an MoD (Navy) specification, this material is subject to specia

2.0966 (CuAl10Ni5Fe4) most popular American grade of nickel aluminum bronze with a chemical composition of approximately 10% aluminium, 5% nickel and 3% iron, is readily hot worked and offers a good machinability. The alloy displays good erosion and cavitation resistance in seawater and brackish wat

Molybdenum is a refractory metal that is very useful in many industrial processes and applications that would not be possible with many of the more common metals and alloys. Refractory metals and alloys are extraordinarily resistant to heat and have unique physical properties.PropertiesGeneralProper

Molybdenum is a refractory metal that is very useful in many industrial processes and applications that would not be possible with many of the more common metals and alloys. Refractory metals and alloys are extraordinarily resistant to heat and have unique physical properties.PropertiesGeneralProper

The increase in the Al and Fe content results in a material in which the hard gamma 2 phase (about 400 HB) is present. By proper metallurgical control this hard constituent is uniformly distributed giving this alloy its ability to resist wear.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C7.

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.66 g/cm³H22AA Standards, ASTM B209MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus70.0 GPaH22AA Standards, ASTM B209Plane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 5000 Series AluminiumPoisson

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.67 g/cm³H112AA Standards, ASTM B209MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus70.0 GPaH112AA Standards, ASTM B209Plane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 5000 Series AluminiumPoiss