PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.7 g/cm³T61EN 573-3, EN 1386, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 90°2.0 °/tT61EN 573-3, EN 4852.5 °/tT61EN 573-3, EN 4854.0 °/tT61EN 573-3, EN 4855.0 °/tT61EN 573-3, EN 4857.0 °/tT61EN 573-3, EN

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.7 g/cm³T42EN 573-3, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 90°1.5 °/tT42EN 573-3, EN 4852.0 °/tT42EN 573-3, EN 4853.0 °/tT42EN 573-3, EN 4854.0 °/tT42EN 573-3, EN 485Elastic modulus70.0 GPaT42EN 573

From the type of alloy AlMgSi is the alloy AlMgSi1 that, which used longest. This cold and/or hot hardenable material reaches strength values of 200 to 315 MPa with A5-elongation at break of approx. 6 to 18 %. In hot and cold-hardened condition is this alloy only limited formable, in the soft materi

Aluminum DIN 3.1655 is a popular age-hardenable alloy known for its free-machining characteristics and mechanical properties. It can be machined to very close tolerances while still maintaining a smooth and bright finish. Unlike other aluminum alloys, DIN 3.1655 does not offer good corrosion resista

Aluminum DIN 3.1355, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneral

The alloy AlCuMg1 belongs to the type of alloy (AlCuMg type), which found of the aluminum wrought machine materials as first in the technology use. Alloys of this type are cold and warm hardenable. They reach thereby high mechanical strength and are relatively heat resistant even in soft condition.

The alloy AlCu2,5Mg0,5 (see also AlCu2,5Mg0,5, material number 3.1124, Werkstoffleistungsblätter der Deutschen Luftfahrt WL 3.1124, part of 1 and part of 100, Ausgn. 12.87) belongs to the type of alloy Al-Cu-Mg, which found of the aluminum wrought machine materials as first in the technology use. Al

DIN 3.1255 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy DIN 3.1255 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity20.0 °C2.8

The material AlMgSiPb is a free-cutting alloy (boring and turning quality). It is warm and cold hardenable. Breaking the splinter is caused by the additive of Pb, and thus a troublefree splinter removal is possible with relatively high cutting performance. From the standardised free-cutting steel al

The alloy AlMn1Mg1 has similar properties like AlMn1, however it reaches higher strength (to F 26). It has also relatively high strength in the soft condition, but it is well cold fomrable. The alloy belongs to the nature-hard aluminum materials. A strength increase can be achieved, not by a purpose

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.72 g/cm³H36EN 573-3, EN 1592, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 180°3.0 °/tH36EN 573-3, EN 485Bending angle 90°1.0 °/tH36EN 573-3, EN 4851.5 °/tH36EN 573-3, EN 4852.5 °/tH36EN 573-3, EN 485Elas

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.72 g/cm³H34EN 573-3, EN 1592, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 180°2.0 °/tH34EN 573-3, EN 485Bending angle 90°0.5 °/tH34EN 573-3, EN 4851.0 °/tH34EN 573-3, EN 4851.5 °/tH34EN 573-3, EN 485Elas

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.72 g/cm³H32EN 573-3, EN 1592, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 180°1.0 °/tH32EN 573-3, EN 4851.5 °/tH32EN 573-3, EN 485Bending angle 90°0.5 °/tH32EN 573-3, EN 4851.0 °/tH32EN 573-3, EN 4851.5

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.72 g/cm³H26EN 573-3, EN 1592, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 180°3.0 °/tH26EN 573-3, EN 485Bending angle 90°1.0 °/tH26EN 573-3, EN 4851.5 °/tH26EN 573-3, EN 4852.5 °/tH26EN 573-3, EN 485Elas

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.72 g/cm³H111EN 573-3, EN 485MechanicalPropertyValueConditionRelated StandardsCommentBending angle 180°0.5 °/tH111EN 573-3, EN 4851.0 °/tH111EN 573-3, EN 485Bending angle 90°1.0 °/tH111EN 573-3, EN 4852.0 °/tH111EN 573-3, EN 485Elastic

The alloy AlMn1Mg0,5 is similarly to AlMn1 in its properties. It reaches strength up to F 25. The alloy belongs to the nature-hard aluminum materials. A strength increase can only occure by cold forming. It is very well hot and cold formable and is suitable to the deep-drawing (no lappet formation).

Quantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process optimisation, quality monitoring, sample analysis, prototyping, trainingPropertiesGeneralPropert

The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a stre

Quantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process optimisation, quality monitoring, sample analysis, prototyping, trainingPropertiesGeneralPropert

Quantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process optimisation, quality monitoring, sample analysis, prototyping, trainingPropertiesGeneralPropert