The austenitic steel X3CrNiCuMo17-11-3-2 is used in solution annealed condition in the form of rods, wire rod and profiles. It is resistant to intercrystalline corrosion also in sensitized condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8 g/cm³MechanicalPropertyTemperatureValueComme

The steel is used for rail vehicle engineering acc. to the selected standard DIN 5512-3.The corresponding properties of EN 10088 shall be taken.Application example: tanksRemarks: For higher chemical loading and for welded constructions ≤ 6 mm sheet thickness. Resistant to intercrystalline corrosion

PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.7 g/cm³FEN 573-3, EN 570Strip, Sheet, PlateMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus68.0 - 70.0 GPaTypical for Wrought 1000 Series AluminiumHardness, Brinell19.0 [-]FEN 573-3, EN 570Strip, Sheet,

Quantity: One truck load – Specialty products on request.Additional services: Via Cindal (the Aludium R&D department): R&D services, benchmarking, chemical audits, material specification, process optimisation, quality monitoring, sample analysis, prototyping, trainingPropertiesGeneralPropert

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.68 g/cm³FEN 573-3, EN 4852.69 g/cm³FEN 573-3, EN 485MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus69.0 GPaFEN 573-3, EN 48570.0 GPaFEN 573-3, EN 485Plane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wr

The alloy AlFeSi is alloyed for increasing the strength increase with Fe and Si. The material belongs to the nature-hard aluminum materials. A strength increase can be achieved only by cold forming. The alloy AlFeSi is very well cold and warm formable and has a good thermal and relatively good elect

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.71 g/cm³H28AA Standards, ASTM B209MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 5000 S

PropertiesGeneralPropertyValueConditionRelated StandardsDensity2.73 g/cm³H19AA Standards, ASTM B209MechanicalPropertyValueConditionRelated StandardsCommentElastic modulus69.5 - 70.0 GPaTypical for Wrought 3000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical for Wrought 3000 S

The following is valid for the material ZP12 with the material number ZP1110: according to DIN EN 12844, the temperature coefficient of the length is 24 µm/m*K.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C6 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C82 GPaElongatio

The platinum-tungsten material PtW5, also Pt95W5 o Pt5W, for jewelery alloys Pt/W950 or Pt950/W50, is used as electrode material for spark plugs, as contact material for switch contacts (switches and relays for higher AC loads with long life like PtIr5, but for DC loads or AC loads with mains-synchr

The platinum-tungsten material PtW5, also Pt95W5 o Pt5W, for jewelery alloys Pt/W950 or Pt950/W50, is used as electrode material for spark plugs, as contact material for switch contacts (switches and relays for higher AC loads with long life like PtIr5, but for DC loads or AC loads with mains-synchr

The material PtRh20 (in the literature also Pt20Rh, Pt80Rh20 or PtRh80/20) is used for highly stressed laboratory equipment, catalysts, electrodes, glass fiber nozzles and lining materials, for crucibles, casings and stirrers in viscometry as well as for glass melting tanks. The mechanical, thermal

The material PtRh10 (in the literature also Pt10Rh, Pt90Rh10 or PtRh90/10) is used for highly stressed laboratory equipment, such as crucibles for melt digestion of minerals and ferroalloys as well as for crucibles, casts and stirrers in viscometry also in the fine grain stabilized state. Furthermor

Aluminum EN AW-5005 is a lean aluminum magnesium alloy with low density and excellent thermal conductivity. This medium strength non-heat-treatable alloy is known for its corrosion resistance in alkaline marine situations. Aluminum EN AW-5005 is readily machinable, and can be welded using TIG and MI

High tensile strength, excellent elongation, and fatigue resistance enable optimized design and light weighting. PropertiesGeneralPropertyTemperatureValueDensity23.0 °C2.76 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C70 - 72 GPaElongation23.0 °C8 - 12 %Fatigue strength23.0 °C

Properties: - 17%-Cr-steel with Mo additives - high polishable - higher resistance to media which arise in drive operation (road salt) - especially developed for automobile industry Application: - as hub caps, fender, radiator cowling, window frame - aprons for headlights, tail light, decorative par

Cold-rolled narrow strip made of the alloy steel 34CrMo4 will be delivered in thicknesses up to 6 mm for quenching and tempering and for quenched and tempered cold strip in thicknesses between 0.3 mm and 3.0 mm in following conditions: - soft annealed or soft annealed and little rerolled (+A or +LC)

The steel 80CrV2 is used as cold rolled strip for springs and special applications in thicknesses of up to 6 mm and as tempered cold strip in thicknesses from 0.30 to 3.00 mm.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.81 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100

The steel 102Cr6 is used as cold rolled strip for springs and special applications in thicknesses of up to 6 mm and as tempered cold strip in thicknesses from 0.30 to 3.00 mm.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.81 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C21

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation A5023.0 °C12 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelRed