CrAl 44 is an ferritic aluminium-chromium material (heating conductor material) used at extrem alternating temperature loading from 1250 to 1350 °C. Application: thin sheet as carrier material for vehicle exhaust-gas catalysts, industry furnace partsPropertiesGeneralPropertyTemperatureValueDensity20

The material LC-Ni99.6 with the material number 2.406 is applied in the form of strips, sheets, tubes, bars, wires and forgings for corrosion-resistant construction components, built-in parts for light bulbs and thermionic valves. It is similar to the material LC-Ni99, yet with a minor change in the

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C40 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

The creep-resistant Ni-Cu-wrought alloy NiCu30Al (K-Monel) is used in form of bars and forged pieces for high corrosion resistant and highest strength parts up to 450°C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.46 g/cm³MechanicalPropertyTemperatureValueElastic modulus20.0 °C178.54 GPa

The steel is used for rail vehicle engineering acc. to the selected standard DIN 5512-3.Application example: railcar bodyRemark: resistant to intercrystalline corrosion in the delivery and the welded conditionPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 g/cm³MechanicalPropertyTemperatu

Material X2CrNi19-11a modifikation of 1.4301 is comparable to X 2CrNi 19 11 acc. to DIN 17440 : 1985-07. The steel shows owing to the lowered C-content resistance to intercrystalline corrosion both in delivery and sensitized condition. Application in chemical apparatus engineering and in pharmaceuti

The material NiCr20CuMo with the material number 2.4660 is applied in the form of strips, sheets, tubes, bars, wires and forgings for corrosion-resistant construction components. The alloy has an excellent resistance to corrosion in sulphuric, phosphoric and organic acids as well as in aqueous solut

According to VdTÜV-Wbl 436 : 2002-09, the material NiMo28 with the material number 2.4617 is used for pressure vessels according to TRB 100 and, with interpreting the AD-Merkblatt editions W 2 and W 10 faithfully to their meaning, for temperatures from -196 to 400 degrees. Furthermore, the highly co

6 mm sheet thickness. Resistant to intercrystalline corrosion in the delivery and the welded condition.Additional services: To ensure our customers' processes and/or products attain – and even exceed – their performance expectations, we offer a wide range of services within both the technical a

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C28 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

CuZn40 (CW509L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn37. Corrosion resistance is similar to pure copper. Processing properties: warm forming: very good cold forming: goo

The ferritic material X2CrMoTiS18-2 as a patented steel is used in the form of rods, wire rod and profiles. No resistance to intercrystalline corrosion in welded condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C2

The material NiCr23Fe with the material number 2.4851 is applied in the form of strips, sheets, tubes, bars and wires for heat-resistant and corrosion-resistant construction components. Due to the Al- and high Cr-content, the alloy possesses a good resistance to oxidation at high temperatures. In co

DILLINAL 460/630 is a weldable normalized fine grained steel which is characterised by a minimum yield strength of 460 MPa and a minimum tensile strength of 630 MPa. DILLINAL 460/630 is mainly applied for the construction of tanks for the transport of liquefied gas with road and rail vehicles where

DIWA 353 is a weldable steel for higher temperature service. It is characterized by high 0.2 % proof stress at elevated temperatures. DIWA 353 is produced using basic oxygen steelmaking process. Its properties are achieved by normalizing and tempering. It is used as plate or formed part for boilers,

AMPCO® 25 is a patented alloy which displays outstanding mechanical properties. The extreme hardness, linked with an excellent compressive strength and very good friction properties, makes it ideal as a forming and drawing die material. As the elongation of the material is nil, thin sections should

AMPCO® 25 is a patented alloy which displays outstanding mechanical properties. The extreme hardness, linked with an excellent compressive strength and very good friction properties, makes it ideal as a forming and drawing die material. As the elongation of the material is nil, thin sections should

AMPCO® 25 is a patented alloy which displays outstanding mechanical properties. The extreme hardness, linked with an excellent compressive strength and very good friction properties, makes it ideal as a forming and drawing die material. As the elongation of the material is nil, thin sections should

AMPCO® 25 is a patented alloy which displays outstanding mechanical properties. The extreme hardness, linked with an excellent compressive strength and very good friction properties, makes it ideal as a forming and drawing die material. As the elongation of the material is nil, thin sections should

This steel is manufactured to the highest quality standards in order to meet the most stringent specifications. The reference standard is API 5L (American Petroleum Institute). Special requirements such as HIC (hydrogen-induced cracking) resistance or high ductility at low temperature can be met to