Gold (Au) is a reddish-yellow, in very thin films blue-green translucent, cubic crystallizing precious metal. It is one of the heaviest metals, is relatively soft and very elastic. Among all metals, it has the best hot and cold ductility and can be hammered down to foil up to 0.0001 mm thick. Gold,

Chemical composition: DIN 17851TiAl6V6Sn2 with the material number 3.7175 (see also TiAl6V6Sn2, material number 3.7174, according to the Werkstoff-Leistungsblatt der Deutschen Luftfahrt WL 3.7174) belongs to the hardenable alpha + beta-titanium alloys. It is similar to the 3.7164 or 3.7165 (TiAl6V4)

Titanium DIN TiAl6Sn2Zr4Mo2Si is a two-phase, Alpha Beta Alloy. It is usually used in the annealed or solution treated and aged conditions. It’s a heat treatable, high strength alloy with lower toughness and ductility than Titanium Grade 5 (6Al-4V) and it’s difficult to weld. Cold forming of DIN TiA

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C42 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C38 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation23.0 °C34 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

The material X6CrNiMoTi17-12-2 is comparable to X 6 CrNiMoTi 17 12 2 nach DIN 17440 : 1985-07. The material is a variant of 1.4401, stabilized by Ti. Increased corrosion resistance owing to the high Mo-content, especially to non oxidizing acids and halogenated media. Application in chemical apparatu

Material X2CrNiMo17-12-2 is comparable to X 2 CrNiMo 17 13 2 acc. to DIN17440 : 1985-07. It is a modification of steel 1.4401 with high resistance to non oxidizing acids and chloride containing media. This steel is suitable for mirror finishing and very good cold formable. Its corrosion properties a

Material X8CrNiS18-9 an austenitic free cutting steel, is comparable to X 10 CrNiS 18 9 acc. to DIN 17440 : 1985-07. It is used for the production of rust-resistant turning parts in food and dairy industry, in photo, color, oil, soap, paper and textile industry. Machinability is due to the sulphur c

Material X10CrNi18-8 is comparable to X 12 CrNi 17 7 acc. to SEW 400 :1991-02 and DIN 17224 : 1982-02. The austenitic CrNi-steel with a lowered Cr- and Ni-content shows strong solidification during the cold forming process. Application when sufficient corrosion resistance and high strength are reque

The in the quenched and tempered condition flame and induction hardenable unalloyed special steel has a, compared to the common quenched and tempered steel, constricted range of the C content and a lower maximum value of the P content. The steel is suitable for flash welding, if prooved conditions w

The in the quenched and tempered condition flame and induction hardenable unalloyed special steel has a, compared to the common quenched and tempered steel, constricted range of the C content and a lower maximum value of the P content. The steel is suitable for flash welding, if prooved conditions w

TH 415 is a single cold rolled band (black plate in coils) of soft unalloyed steel and in the surface qualities plain, stone finish and matt for conventional packaging sheet. The band is produced in thicknesses of 0,17 to 0,49 mm in steps of 0,005 mm. The surface is oiled in order to avoid corrosion

CuZr, mat. No CW120C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuZr, mat. No 2.1580, acc. to DIN 17666 : 1983-12 applies: The strength properties of CuZr are not as favorable as for CuCrZr but it very well meets high requirements to tempering strength and creep

PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °C184 GPa500.0 °C175 GPa600.0 °C164 GPaElongation20.0 °C6 %Poisson's ratio20.0 °C0.28 [-]Shea

The material Ni99.2 with the material number 2.4066 is applied in the form of strips, sheets, tubes, bars, wires and forgings for corrosion-resistant construction components, built-in parts for light bulbs and thermionic valves. Ni99.2 is technically pure nickel with high ductility, good thermal con

Material X5CrNiMo17-12-2 is comparable to X 5 CrNiMo 17-12-2 acc. to DIN17440 : 1985-07. This material is an austenitic CrNiMo-steel with increased resistance to non oxidizing acids and halogenated media but to intercrystalline corrosion only in delivery condition. It is suitable for mirror finishin

TH 435 is a single cold rolled band (black plate in coils) of soft unalloyed steel and in the surface qualities plain, stone finish and matt for conventional packaging sheet. The band is produced in thicknesses of 0,17 to 0,49 mm in steps of 0,005 mm. The surface is oiled in order to avoid corrosion

6 mm sheet thickness. Resistant to intercrystalline corrosion in the delivery and the welded condition.Additional services: To ensure our customers' processes and/or products attain – and even exceed – their performance expectations, we offer a wide range of services within both the technical a

CuZn40 (CW509L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn37. Corrosion resistance is similar to pure copper. Processing properties: warm forming: very good cold forming: goo