Cold-rolled narrow strip made of the alloy steel 34CrMo4 will be delivered in thicknesses up to 6 mm for quenching and tempering and for quenched and tempered cold strip in thicknesses between 0.3 mm and 3.0 mm in following conditions: - soft annealed or soft annealed and little rerolled (+A or +LC)

Cold-rolled narrow strip made of the alloy steel 25Mn4 will be delivered in thicknesses up to 6 mm for quenching and tempering in following conditions: - soft annealed or soft annealed and little rerolled (+A or +LC), - cold rolled (+CR). The delivery condition annealed to globular carbides (+AC) ca

Material CuZn35Pb1, mat. No. CW600N, is an unhardenable wrought alloy. to the comparable make CuZn36Pb, mat. No. 2.0331 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unleaded b

Material CuZn35Pb1, mat. No. CW600N, is an unhardenable wrought alloy. to the comparable make CuZn36Pb, mat. No. 2.0331 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unleaded b

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn30 (CW505L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn28. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn30 (CW505L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn28. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn30 (CW505L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn28. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn20 (CW503L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are worse than for CuZn15. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderately cold forming: go

Aluminum JIS 2024, known for its use in aircraft industry, is an alloy that offers excellent strength. When in the annealed condition it is readily formed and has good machinability. Though it has a relatively low level of corrosion resistance, it can be machined to a high finish.PropertiesGeneralPr

Aluminum JIS 2017 is a heat treatable wrought alloy that offers decent strength, ductility, and good machinability. Aluminum JIS 2017 offers more strength than Aluminum 2011, and has fair workability and corrosion resistance. As with many aluminum alloys, Aluminum JIS 2017 should not be welded as it

Aluminum JIS 2017 is a heat treatable wrought alloy that offers decent strength, ductility, and good machinability. Aluminum JIS 2017 offers more strength than Aluminum 2011, and has fair workability and corrosion resistance. As with many aluminum alloys, Aluminum JIS 2017 should not be welded as it

Aluminum JIS 2017 is a heat treatable wrought alloy that offers decent strength, ductility, and good machinability. Aluminum JIS 2017 offers more strength than Aluminum 2011, and has fair workability and corrosion resistance. As with many aluminum alloys, Aluminum JIS 2017 should not be welded as it

JIS 2014 is an alloy with strength, machinability and welding capabilities, Aluminum Alloy JIS 2014 is an excellent option. It is a precipitation hardening alloy that maintains strength after heat treatment.PropertiesGeneralPropertyValueCommentDensity2.75 - 2.84 g/cm³Typical for Wrought 2000 Series

JIS 1100 is a soft, non-heat-treatable and low strength alloy that offers strong corrosion resistance. Composed of 99% aluminum and 0.12% copper, JIS 1100 is purest grade of aluminum alloy available commercially.PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series Alu

JIS 1100 is a soft, non-heat-treatable and low strength alloy that offers strong corrosion resistance. Composed of 99% aluminum and 0.12% copper, JIS 1100 is purest grade of aluminum alloy available commercially.PropertiesGeneralPropertyValueCommentDensity2.7 g/cm³Typical for Wrought 1000 Series Alu

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelDimensionPropertyValueWall thickness1 - 8 mmMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation A523.0 °C16 - 35 %Elongation A5, tra

PropertiesGeneralPropertyTemperatureValueCommentDensity20.0 °C7.8 - 7.9 g/cm³Typical for High Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C200 - 215 GPaTypical for High Carbon SteelElongation A520.0 °C18 %Elongation A5, transverse20.0 °C14 %Hardness, Brinell20.0 °C167 [