CuPb1P, mat. No CW113C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuPb1P, mat. No 2.1160, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. The material shows a very high electrical and thermal conductivity as well as

CuPb1P, mat. No CW113C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuPb1P, mat. No 2.1160, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. The material shows a very high electrical and thermal conductivity as well as

Material CuNi18Zn19Pb1, mat. No. CW408J is an alloy of high strength and hardness. To the comparabel mark CuNi18Zn19Pb1, mat. No. 2.0790, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperat

Material 16Mo3, material number 1.5415 is a high-temperatuare alloyed high-grade steel for pressure vessel and apparatus engineering. It is applicable in permanent operation up to approx. 530 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 - 7.86 g/cm³50.0 °C7.84 g/cm³100.0 °C7.82 g/c

Material 16Mo3, material number 1.5415 is a high-temperatuare alloyed high-grade steel for pressure vessel and apparatus engineering. It is applicable in permanent operation up to approx. 530 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 - 7.86 g/cm³50.0 °C7.84 g/cm³100.0 °C7.82 g/c

Material CuNi12Zn30Pb1, mat. No. CW406J is an alloy of high strength and hardness. To the comparabel mark CuNi12Zn30Pb1, mat. No. 2.0780, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperat

Wire fom copper alloy for general purposes.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 - 8.44 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C102 GPaElongation20.0 °C8 %Elongation A10020.0 °C2 - 3 %Elongation A11.320.0 °C5 %Poisson's ratio20.0 °C0.34 [-]Shear

The high temperature material 14MoV6-3, material number 1.7715, is used in pressure vessel construction. It is owing to its good high-temperature strength properties favorable at high pressures in a temperature range from 500 to 560 °C. Application for welded collars and flanges.PropertiesGeneralPro

Material 13CrMo4-5, material number 1.7335 is used in pressure vessel construction. Application in boiler construction, for collectors, flanges and welded collars, in apparatus engineering and in petrochemistry.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³50.0 °C7.84 g/cm³100.0 °

Material 13CrMo4-5, material number 1.7335 is used in pressure vessel construction. Application in boiler construction, for collectors, flanges and welded collars, in apparatus engineering and in petrochemistry.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³50.0 °C7.84 g/cm³100.0 °

CuZr, mat. No CW120C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuZr, mat. No 2.1580, acc. to DIN 17666 : 1983-12 applies: The strength properties of CuZr are not as favorable as for CuCrZr but it very well meets high requirements to tempering strength and creep

CuZr, mat. No CW120C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuZr, mat. No 2.1580, acc. to DIN 17666 : 1983-12 applies: The strength properties of CuZr are not as favorable as for CuCrZr but it very well meets high requirements to tempering strength and creep

Steel C40 is suitable for larger forged parts in vehicle manufacturing and machine engineering (e.g. road wheels, axles).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureValueElastic modulus-100.0 °C217 GPa20.0 °C210 - 212 GPa100.0 °C205 - 207 GPa20

Material CuZn39Pb0,5, mat. No. CW610N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb0,5, mat. No. 2.0372 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unlea

Application: general purpose wire, springs, fastenersPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C135 GPaElongation20.0 °C20 %Elongation A10020.0 °C8 - 12 %Elongation A11.320.0 °C15 %Poisson's ratio23.0 °C0.34 [-]

Application: general purpose wire, springs, fastenersPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C135 GPaElongation20.0 °C12 %Elongation A10020.0 °C5 - 8 %Elongation A11.320.0 °C10 %Poisson's ratio23.0 °C0.34 [-]T

CW607N is suited for cold forming and easy to machine.Application: bending, riveting, embossing and upsetting partsPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 - 8.44 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C102 GPaElongation20.0 °C20 - 25 %Elongation A10020.

Application: general purpose wire, springs, fastenersPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.9 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C135 GPaElongation20.0 °C15 %Elongation A10020.0 °C6 - 10 %Elongation A11.320.0 °C12 %Poisson's ratio23.0 °C0.34 [-]

CW607N is good to very good cold formable and machinable.Application: bending, riveting, embossing and upsetting partsPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C102 GPaElongation20.0 °C12 - 15 %Elongation A1020.0 °C1

CW606N is a machinable brass.Application: extruded and drawn productsPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 - 8.45 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C105 GPaElongation20.0 °C8 %Elongation A1020.0 °C6 %Elongation A10020.0 °C2 - 4 %Elongation A11.32