Material CuNi18Zn20, mat. No. CW409J is an alloy of high strength and hardness. To the comparabel mark CuNi18Zn20, mat. No. 2.0740, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatures.

Material CuNi18Zn20, mat. No. CW409J is an alloy of high strength and hardness. To the comparabel mark CuNi18Zn20, mat. No. 2.0740, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatures.

Steel C60E is suitable for larger parts (heavy forged parts) of high load in vehicle, engine and machine engineering. Surface hardenable (e.g. crankshafts, bolts, transmission parts). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, i

Steel C60E is suitable for larger parts (heavy forged parts) of high load in vehicle, engine and machine engineering. Surface hardenable (e.g. crankshafts, bolts, transmission parts). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, i

Steel C60E is suitable for larger parts (heavy forged parts) of high load in vehicle, engine and machine engineering. Surface hardenable (e.g. crankshafts, bolts, transmission parts). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, i

Steel C50R is suitable for parts in vehicle, engine and machine engineering that require enhanced workability at constant strength qualities (e.g. transmission shafts, gear wheels). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in

Steel C50R is suitable for parts in vehicle, engine and machine engineering that require enhanced workability at constant strength qualities (e.g. transmission shafts, gear wheels). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in

Steel C50R is suitable for parts in vehicle, engine and machine engineering that require enhanced workability at constant strength qualities (e.g. transmission shafts, gear wheels). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in

Steel C50E is suitable for larger parts (heavy forged parts) in vehicle, engine and machine engineering (e.g. transmission parts, shafts, wheel hubs). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in various conditions (see DIN EN

Steel C50E is suitable for larger parts (heavy forged parts) in vehicle, engine and machine engineering (e.g. transmission parts, shafts, wheel hubs). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in various conditions (see DIN EN

Steel C50E is suitable for larger parts (heavy forged parts) in vehicle, engine and machine engineering (e.g. transmission parts, shafts, wheel hubs). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in various conditions (see DIN EN

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical

PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Wrought 5000 Series AluminiumMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus69.0 - 70.0 GPaTypical for Wrought 5000 Series AluminiumPlane-Strain Fracture Toughnes22.0 - 35.0 MPa·√mTypical

Copper plates, sheet and circles for boilers, pressure vessels and hot water storage units.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.9 - 8.94 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C129 - 132 GPaElongation20.0 °C33 - 42 %Hardness, Vickers20.0 °C55 [-]Poisso

CuZn40 (CW509L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn37. Corrosion resistance is similar to pure copper. Processing properties: warm forming: very good cold forming: goo

Material CuZn39Pb2, mat. No. CW612N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb2, mat. No. 2.0380 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unleaded

Material CuZn39Pb2, mat. No. CW612N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb2, mat. No. 2.0380 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unleaded

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo