The austenitic steel X2CrNi18-9 is available in solution annealed condition in the form of colled rolled band, warm rolled band and warm rolled sheet. The material is resistant to intercrystalline corrosion also in welded condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.9 g/cm³Mech

The make X1CrNiMoCuN20-18-7 is applicated in solution annealed condition in the form of colled rolled band, warm rolled band and warm rolled sheet as well as in the form of bars, wire rod and profiles. The material is resistant to intercrystalline corrosion also in sensitized condition.PropertiesGen

The make X17CrNi16-2 is comparable to X 20 CrNi 17-2 acc. to DIN 17440 :1985-07. The material is a heat-treatable 17%-chromium-steel of favorable resistance to water, low acids and bases as well as to stronger oxidizing acids (e.g. nitrous acid). Application for high loaded machine parts such as pum

Cu-DHP, mat. No CW021A, is a deoxidized copper with low phosphorus-content. To the comparable DIN-mark SF-Cu, mat. No 2.0070 acc. to DIN 1787: 1973-01 (precondition for the comparability: Cu-content min. 99,95%, deoxidation agent phosphorus) applies: The material is also available in a special quali

CuZn40 (CW509L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn37. Corrosion resistance is similar to pure copper. Processing properties: warm forming: very good cold forming: goo

Steel 28Mn6 is usable for lower strained weldable parts in vehicle, engine and machine engineering (e.g. cardan shafts, camshafts, gear wheels).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.82 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0

Steel 28Mn6 is usable for lower strained weldable parts in vehicle, engine and machine engineering (e.g. cardan shafts, camshafts, gear wheels).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.82 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0

Material CuZn40Pb2, mat. No. CW617N, is an unhardenable wrought alloy. to the comparable make CuZn40Pb2, mat. No. 2.0402 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn40. Machi

CuZn40Mn1Pb1 (CW720R former identification: CuZn40MnPb) is an unhardenable copper alloy. High hardness and strength parameter are achievable by cold forming only. Manganes increases corrosion resistance and sliding qualities. Improved machinability by Pb-addition. Processing properties: warm forming

Steel C55 is suitable for higher loaded parts requiring enhanced wear resistance in vehicle manufacturing, engine and gear engineering. Preferred application for parts undergoing a surface hardening, lower risk of tearing for larger and more complex components than C60 (e.g. gear wheels, shafts, ind

Material CuZn39Pb3, mat. No. CW614N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb3, mat. No. 2.0401 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for unleaded bras

Cu-DLP, mat. No CW023A, is a deoxidized copper with limited, low residual copper-content. To the comparable DIN-make SW-Cu, mat. No 2.0076 acc. to DIN 1787 : 1973-01 applies: Tensile strength and Brinell hardness are increasable by cold forming. SW-Cu is hydrogen resistant and shows the lowest therm

Cu-DLP, mat. No CW023A, is a deoxidized copper with limited, low residual copper-content. To the comparable DIN-make SW-Cu, mat. No 2.0076 acc. to DIN 1787 : 1973-01 applies: Tensile strength and Brinell hardness are increasable by cold forming. SW-Cu is hydrogen resistant and shows the lowest therm

Cu-DLP, mat. No CW023A, is a deoxidized copper with limited, low residual copper-content. To the comparable DIN-make SW-Cu, mat. No 2.0076 acc. to DIN 1787 : 1973-01 applies: Tensile strength and Brinell hardness are increasable by cold forming. SW-Cu is hydrogen resistant and shows the lowest therm

Copper for electrolytically tinned strip.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.9 - 8.94 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-253.0 °C138 GPa-195.0 °C136 GPa-100.0 °C133 GPa20.0 °C128 - 132 GPa50.0 °C127 GPa100.0 °C125 GPa150.0 °C122 GPa200.0 °C120 GPa250.0

Steel C60 is suitable for parts of high strength and higher requirements to wear resistance in vehicle, engine and machine engineering, surface hardenable (e.g. transmission parts, shafts, axles). Further application in toolmaking. Lowest application temperature -25 °C. As a bright steel product it

Steel C50 is suitable for parts of higher requirements to strength and wear resistance in vehicle, engine and machine engineering (e.g. shafts, hubs). Lowest application temperature -25 °C, most favorable application area 5 to 10 mm nominal size. As a bright steel product it is used in the form of b

Steel C45 is suitable for mean loaded parts in vehicle, engine and machine engineering (e.g. transmission shafts, gear wheels, clutch parts). Lowest application temperature -25 °C, favorable creep behaviour up to 480°C. As a bright steel product it is used in the form of bars, bright, straight, in v

Steel C40 is suitable for larger forged parts in vehicle and machine engineering (e.g. road wheels, axles). Lowest application temperature -25°C. As a bright steel product it is used in the form of bars, bright, straight, in various conditions (see DIN EN 10277 : 1999-10).PropertiesGeneralPropertyT

Steel C35 is suitable for parts of slightly higher strength requirements and still low ductility requirements in vehicle, engine and machine engineering (e.g. gears, bolts, clutch parts). Lowest application temperature -25°C, favorable creep behaviour up to 480°C. As a bright steel product it is us