The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a stre

The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a stre

The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a stre

Food safe aluminum.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.7 g/cm³H14EN 573-3, EN 1301Strip, Sheet, Plate20.0 °C2.7 g/cm³H14EN 573-3WireMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus-270.0 °C70.0 GPaH14EN 573-3Wire70.0

Food safe aluminum.PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.7 g/cm³FEN 573-3, EN 1715-3, EN 1715-4, EN 485, EN 570Strip, Sheet, Plate, Wire20.0 °C2.7 g/cm³FEN 573-3FlatMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentElastic modulus-270.

Aluminium casting alloy (pressure die casting, investment casting)PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Cast 3xx.x Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus73.0 - 80.0 GPaTypical for Cast 3xx.x Series AluminiumHardn

Aluminium casting alloy (pressure die casting)PropertiesGeneralPropertyValueCommentDensity2.65 - 2.71 g/cm³Typical for Cast 4xx.x Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentBending Fatigue Strength60.0 - 90.0 MPaFEN 1706CastingElastic modulus71.0 - 75.0 GPaTypical f

Aluminium casting alloy (sand casting, permanent mould casting, pressure die casting)PropertiesGeneralPropertyValueCommentDensity2.65 - 2.71 g/cm³Typical for Cast 4xx.x Series AluminiumMechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60.0 - 90.0 MPaFEN

Aluminium casting alloy (pressure die casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³FEN 1706Casting20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60.0 - 90.0 MPaFEN 1706Castin

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³FEN 1706, EN 13195Casting20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60

Aluminium casting alloy (sand casting, permanent mould casting, investment casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsDensity20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60.0 - 90.0 MPaFEN 170

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.65 g/cm³FEN 1706, EN 13195Casting20.0 °C2.65 g/cm³FEN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength60

Aluminium casting alloy (pressure die casting)PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Cast 3xx.x Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus73.0 - 80.0 GPaTypical for Cast 3xx.x Series AluminiumHardness, Brinell60.0 [-]

Aluminium casting alloy (pressure die casting)PropertiesGeneralPropertyValueCommentDensity2.65 - 2.7 g/cm³Typical for Cast 3xx.x Series AluminiumMechanicalPropertyValueConditionRelated StandardsShapeCommentElastic modulus73.0 - 80.0 GPaTypical for Cast 3xx.x Series AluminiumHardness, Brinell80.0 [-]

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.75 g/cm³T64EN 1706Casting20.0 °C2.75 g/cm³T64EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 1

Aluminium casting alloy (sand casting, permanent mould casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.75 g/cm³T6EN 1706Casting20.0 °C2.75 g/cm³T6EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigue Strength80.0 - 110

Aluminium casting alloy (sand casting, permanent mould casting, investment casting)PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity2.75 g/cm³T4EN 1706Casting20.0 °C2.75 g/cm³T4EN 1706MechanicalPropertyTemperatureValueConditionRelated StandardsShapeCommentBending Fatigu

The high-strength material has a high fracture toughness also for larger thicknesses and resistance to stress corrosion also in the ST direction and exfoliation corrosion.It has a low distortion post machining.Application: integral and fittings of larger dimensionsPropertiesGeneralPropertyValueCondi

The high-strength material has a high fracture toughness also for larger thicknesses and resistance to stress corrosion also in the ST direction and exfoliation corrosion.It has a low distortion post machining.Application: integral and fittings of larger dimensionsPropertiesGeneralPropertyValueCondi

The material EN AW-AlCu4SiMg(A) is produced for extruded and drawn components, wire and prewire for mechanical applications. The alloy is used for sheet, strip, forged parts and prematerial. It is not food-safe.PropertiesGeneralPropertyValueConditionRelated StandardsShapeDensity2.8 g/cm³T4510EN 573-