The austenitic ferritic steel X2CrNiN23-4 is available in the solution annealed condition. Welded circular tubes of this steel are used for compression load and for corrosive load at room temperature, low temperatures and elevated temperatures. The material is resistant to intercrystalline corrosion

The austenitic ferritic steel X2CrNiMoN25-7-4 is available in the solution annealed condition. Welded circular tubes of this steel are used for compression load and for corrosive load at room temperature, low temperatures and elevated temperatures. The material is resistant to intercrystalline corro

The austenitic ferritic steel X2CrNiMoCuWN25-7-4 is available in the solution annealed condition. Welded circular tubes of this steel are used for compression load and for corrosive load at room temperature, low temperatures and elevated temperatures. The material is resistant to intercrystalline co

CuZn39Mn1AlPbSi (CW718R former identification: CuZn40Al1) is an unhardenable copper alloy. High hardness and strength values are achievable by cold forming only. Strength properties, corrosion resistance and oxidation resistance are increasable by Al-addition. CuZn39Mn1AlPbSi shows a mean wear resis

CuZn39Mn1AlPbSi (CW718R former identification: CuZn40Al1) is an unhardenable copper alloy. High hardness and strength values are achievable by cold forming only. Strength properties, corrosion resistance and oxidation resistance are increasable by Al-addition. CuZn39Mn1AlPbSi shows a mean wear resis

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn36 (CW507L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn33. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn35Ni3MnAlPb (CW710R former identification: CuZn35Ni2) is an unhardenable copper alloy. High hardness and strength parameter are achievable by cold forming only. Nickel improves strength properties, corrosion resistance and high-temperature resistance. CuZn35Ni3MnAlPb shows favorable weathering a

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

CuZn33 (CW506L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn30. Corrosion resistance is similar to pure copper. Processing properties: warm forming: good cold forming: very goo

Seamless, round tubes from copper alloy for general purposes.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.47 - 8.5 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C102 GPaElongation20.0 °C10 %Shear modulus23.0 °C40 GPaTypical for Wrought Copper BrassTensile strength20.

Wire fom copper alloy for general purposes.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 - 8.45 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C110 GPa100.0 °C106 GPa200.0 °C102 GPa300.0 °C97 GPa400.0 °C89 GPa500.0 °C79 GPaPoisson's ratio20.0 °C0.34 [-]Shear mod

CuZn20 (CW503L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are worse than for CuZn15. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderately cold forming: go

CuZn15 (CW502L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn10. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderately cold forming: go

CuZn10 (CW501L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal conductivity is lower than for CuZn5. Favorable electrical conductivity. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderatel

Steel C 50 is suitable for parts in vehicle manufacturing, engine and machine engineering with higher strength and wear resistance requirements (e.g. shafts, hubs). Lowest application temp. -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureVal

The corrosion resistant material X7CrNiNb18-10, material number 1.4912 is predominantly used for pressure vessel construction.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.9 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C200 GPa100.0 °C194 GPa200.0 °C186 GPa300.0 °C17