PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C22 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C23 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C24 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for Low Carbon SteelElongation20.0 °C26 %Poisson's ratio23.0 °C0.29 [-]Typical for Low Carbon SteelShear m

Material CuZn40Mn1Pb1AlFeSn (CW721R) is used in the form of rods, hollow rods, profiles, forging prematerial and forged parts.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.3 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C96 GPaElongation20.0 °C10 - 20 %Elongation A11.

Steel C50 is suitable for components of higher strength and wear resistance demands in vehicle manufacturing, engine and machine engineering (e.g. shafts, hubs). Lowest working temperature -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureValu

Material CuZn39Pb3, mat. No. CW614N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb3, mat. No. 2.0401 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for unleaded bras

CW724R is very easy to machine and good resistant to corrosion.Application: drinking water supplyPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.25 - 8.3 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C85 - 100 GPaElongation20.0 °C11 - 12 %Elongation A10020.0 °C10 %Elong

CW724R is very easy to machine and good resistant to corrosion.Application: drinking water supplyPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.25 - 8.3 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C85 - 100 GPaElongation20.0 °C15 %Elongation A10020.0 °C12 %Elongation

= 99,9% and a high residual copper-content. Tensile strength and Brinell hardness are increasable by cold forming. SF-Cu (Cu-DHP) is hydrogen resistant and shows the lowest thermal and electrical conductivity of the pure copper materials. Processing properties: hot forming: very good cold forming:

The standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping, and other utilities. It is primarily applicable to the North Sea Sector, but may als

The standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping, and other utilities. It is primarily applicable to the North Sea Sector, but may als

Steel C 60 is suitable for high ductility parts and parts of increased wear resistance requirements in vehicle manufacturing, engine and machine engineering surface hardenable (e.g. transmission parts, shafts, axles). Additional application in tooling. Lowest application temp. -25 °C.PropertiesGene

Material CuZn40Pb2, mat. No. CW617N, is an unhardenable wrought alloy. to the comparable make CuZn40Pb2, mat. No. 2.0402 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn40. Machi

Steel C55 is suitable for higher strained parts in vehicle, engine and transmission manufacturing that require an enhanced wear resistance. Preferred application for parts undergoing a surface hardening lower risk of tearing for larger and complexer parts than C60 (e.g. transmission gear wheels, sh

CuZn37Mn3Al2PbSi (CW713R former CuZn40Al2) is an unhardenable copper alloy. High hardness and strength parameter are achievable by cold forming only. Strength properties, corrosion resistance and oxidation resistance are increasable by Al-addition. CuZn37Mn3Al2PbSi shows a high wear resistance and i

Steel C55E is suitable for larger parts in vehicle manufacturing, engine and machine engineering undergoing a surface hardening (e.g. gear wheels, screws, shafts).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 - 7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C2

The make X6Cr17 is comparable to X 6 Cr 17 acc. to DIN 17440 : 1985-07. The material is a ferritic steel (17% Cr). Largely resistant in water, steam, low acids and bases and in oxidizing acids (e.g. nitrous acid). As cold rolled sheet for washing machines and kitchen parts, canteens, facings, trim s

Material CuZn39Pb0,5, mat. No. CW610N, is an unhardenable wrought alloy. to the comparable make CuZn39Pb0,5, mat. No. 2.0372 acc. to DIN 17660 : 1983-12 applies: High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for the unlea

CuZn37Mn3Al2PbSi (CW713R former CuZn40Al2) is an unhardenable copper alloy. High hardness and strength parameter are achievable by cold forming only. Strength properties, corrosion resistance and oxidation resistance are increasable by Al-addition. CuZn37Mn3Al2PbSi shows a high wear resistance and i