Material CuNi18Zn20, mat. No. CW409J is an alloy of high strength and hardness. To the comparabel mark CuNi18Zn20, mat. No. 2.0740, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatures.

Material CuNi18Zn20, mat. No. CW409J is an alloy of high strength and hardness. To the comparabel mark CuNi18Zn20, mat. No. 2.0740, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatures.

Material CuNi12Zn24, mat. No. CW403J is an alloy of high strength and hardness. To the comparabel DIN-mark CuNi12Zn24, mat. No. 2.0730, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatur

Material CuNi12Zn24, mat. No. CW403J is an alloy of high strength and hardness. To the comparabel DIN-mark CuNi12Zn24, mat. No. 2.0730, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatur

Material CuNi12Zn24, mat. No. CW403J is an alloy of high strength and hardness. To the comparabel DIN-mark CuNi12Zn24, mat. No. 2.0730, acc. to DIN 17663 : 1983-12 applies: Strength is further increasable due to the high strain hardening capability. The material does not embrittle at low temperatur

Steel X10NiCrSi35-19 shows a highest application temperature of up to 1100 °C in air.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C190 - 210 GPaTypical for SteelElongation20.0 °C40 %Hardness, Brinell20.0 °C200 [-]Poisson&

Steel 51CrV4 is suitable for high loaded parts in aircraft, vehicle, engine and machine engineering that require increased tempering resistance at best core qualities and high wear resistance (e.g.transmission and joint parts, axles). Furthermore application as spring and tool steel.As a bright stee

Steel 42CrMoS4 is suitable for high loaded parts in vehicle, engine and machine engineering with high wear resistance and favorable core qualities as well as enhanced workability (e.g. crankshafts, pinions, balance shafts). The steel shows a high specific resistance to static and dynamic load. Lowes

Steel 42CrMoS4 is suitable for high loaded parts in vehicle, engine and machine engineering with high wear resistance and favorable core qualities as well as enhanced workability (e.g. crankshafts, pinions, balance shafts). The steel shows a high specific resistance to static and dynamic load. Lowes

NiCr28FeSiCe is a highly chrome-containing, austenitic, high-temperature NiCrFe-alloy of controlled contents of silicon and noble earths. The material is particularly suitable for thermical waste incineration plants due to a well protecting, external chromium oxide coat associated with a subjacent s

Cu-DLP, mat. No CW023A, is a deoxidized copper with limited, low residual copper-content. To the comparable DIN-make SW-Cu, mat. No 2.0076 acc. to DIN 1787 : 1973-01 applies: Tensile strength and Brinell hardness are increasable by cold forming. SW-Cu is hydrogen resistant and shows the lowest therm

NiCr15Fe, contained in VdTÜV-material specification 305 : 1984-03 and supplement 305 : 1990-06 is an unhardenable alloy for application in wetchemical sector and at high temperatures. Material`s versatility causes a wide application range from low temperature range up to approx. 1150°C (highest appl

Sort EN-GJS-1200-2, mat. No EN-JS1120 is a ferrous-carbon-based cast material that contains carbon predominantly in the form of spheroidal particles and that combines compared to the sort cast iron with nodular graphite (DIN EN 1563) higher strength and ductility properties by heat-treatment. Heat-t

Sort EN-GJS-1000, mat. No EN-JS1110 is a ferrous-carbon-based cast material that contains carbon predominantly in the form of spheroidal particles and that combines compared to the sort cast iron with nodular graphite (DIN EN 1563) higher strength and ductility properties by heat-treatment. Heat-tre

The free cutting case hardening steel 46SPb20 is used for bulk parts of higher strength, especially for lower ductility demands in transversal direction compared to other C-steels (e.g. C45). Machinability enhancement is achieved by Pb-content. Application in car industry, apparatus, equipment and m

The free cutting case hardening steel 46SPb20 is used for bulk parts of higher strength, especially for lower ductility demands in transversal direction compared to other C-steels (e.g. C45). Machinability enhancement is achieved by Pb-content. Application in car industry, apparatus, equipment and m

The free cutting case hardening steel 46SPb20 is used for bulk parts of higher strength, especially for lower ductility demands in transversal direction compared to other C-steels (e.g. C45). Machinability enhancement is achieved by Pb-content. Application in car industry, apparatus, equipment and m

CuZn20 (CW503L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are worse than for CuZn15. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderately cold forming: go

CuZn15 (CW502L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal and electrical conductivity are lower than for CuZn10. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderately cold forming: go

CuZn10 (CW501L) is an unhardenable wrought alloy. High hardness and strength parameter are achievable by cold forming only. Thermal conductivity is lower than for CuZn5. Favorable electrical conductivity. Corrosion resistance is similar to pure copper. Processing properties: warm forming: moderatel