The fully killed machining steel 35 SPb 20 is used for mass parts of mean strength, especially for lower toughness demands cross-sectional. Its better machinable because of the Pb addition. Application in the automotive engineering, toolbuilding, apparatus engineering (screws, nuts, smal parts).Prop

GS-C 22 Mo 4 is used for turbine parts and pressure vessels at low temperature (300 to 450 °C) and medium pressure, e.g. for housings and armatures.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C211 GPa100.0 °C204 GPa20

GS-17 CrMoV 5 11 is used for thick-walled cast pieces at high temperatures and pressures, e. g. for high loaded turbine housings and jet cases.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C211 GPa100.0 °C204 GPa200.0 °

GS-17 CrMo 5 5 is used for thick-walled cast pieces at high temperatures and pressures, e.g. for housings, armatures and valve boxes.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C211 GPa100.0 °C204 GPa200.0 °C196 GPa30

48 CrMo 4 is an anti-friction bearing steel that can be refined and induction hardened. In the Jominy test it reaches surface hardnesses of approximately 65 HRC. It is used for larger dimensions of anti-friction bearing parts (rings and discs).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7

43 CrMo 4 is an anti-friction bearing steel that can be refined and induction hardened. In the Jominy test it reaches surface hardnesses of approximately 61 HRC. It is used for discs and anti-friction bearing parts of larger dimensions.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.83 - 7.

The fine grained steel WStE 500 (high temperature grade) is used for welded constructions of different kind like pressure vessels, stationary or mobile storage tanks, high pressure lines, bridge and support constructions etc. The application temperature of the high temperature grade amounts to 400 °

The fine grained steel WStE 420 (high temperature grade) is used for welded constructions of different kind like pressure vessels, stationary or mobile storage tanks, high pressure lines, bridge and support constructions etc. The application temperature of the high temperature grade amounts to 400 °

The steel X 6 CrNiTi 18 10 is well suited for cold-forming, however, one must be aware of the increased cold strain hardening compared to carbon steels. Cold-forming is not as good as with steel X 5 CrNi 18 12. The steel is used in chemical eqiupment construction, the fat- and soap industries for st

The steel X 6 CrNiTi 18 10 is well suited for cold-forming, however, one must be aware of the increased cold strain hardening compared to carbon steels. Cold-forming is not as good as with steel X 5 CrNi 18 12. The steel is used in chemical eqiupment construction, the fat- and soap industries for st

The steel X 6 CrNiTi 18 10 is well suited for cold-forming, however, one must be aware of the increased cold strain hardening compared to carbon steels. Cold-forming is not as good as with steel X 5 CrNi 18 12. The steel is used in chemical eqiupment construction, the fat- and soap industries for st

The steel X 6 CrNiMoTi 17 12 2 is well suited for cold-forming, one must be aware of the increased cold strain hardening compared to carbon steels. Cold forming is worse than for X 5 CrNiMo 17 12 2. Its increased corrosion resistance to non-oxidizing acids and substances containing halogen allow it

The steel X 6 CrNiMoTi 17 12 2 is well suited for cold-forming, one must be aware of the increased cold strain hardening compared to carbon steels. Cold forming is worse than for X 5 CrNiMo 17 12 2. Its increased corrosion resistance to non-oxidizing acids and substances containing halogen allow it

The steel X6Cr17 is well suited for cold-forming. The strain hardening inclination is significantly lower than that of stainless austenitic steels and is about equal to that of carbon steel. The ferritic, 17%-Cr steel is used to treat corrosion occurances through water, steam, weak acids, as well as

The steel X6Cr17 is well suited for cold-forming. The strain hardening inclination is significantly lower than that of stainless austenitic steels and is about equal to that of carbon steel. The ferritic, 17%-Cr steel is used to treat corrosion occurances through water, steam, weak acids, as well as

The steel X6Cr17 is well suited for cold-forming. The strain hardening inclination is significantly lower than that of stainless austenitic steels and is about equal to that of carbon steel. The ferritic, 17%-Cr steel is used to treat corrosion occurances through water, steam, weak acids, as well as

The steel X 5 CrNiMo 17 12 2 is very well suited for cold-forming, one must be aware of the increased cold strain hardening compared to carbon steels. Its increased resistance to non-oxidizing acids and substances containing halogen and its abilitity to be high-gloss polished allow it to be used for

The steel X 5 CrNiMo 17 12 2 is very well suited for cold-forming, one must be aware of the increased cold strain hardening compared to carbon steels. Its increased resistance to non-oxidizing acids and substances containing halogen and its abilitity to be high-gloss polished allow it to be used for

The steel X 5 CrNiMo 17 12 2 is very well suited for cold-forming, one must be aware of the increased cold strain hardening compared to carbon steels. Its increased resistance to non-oxidizing acids and substances containing halogen and its abilitity to be high-gloss polished allow it to be used for

G-X 40 NiCrSi 38 18, for highest mechanical loaded parts, like grates (abrupt variation in temperature). The high nickel content is in this case the important fact for heat resistant and reduction the crack initiation danger in case of heat changing loadings resistance: - in oxidising burning atmosp