Seamless precision steel tube made from St 30 Al is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

Seamless precision steel tube made from St 30 Al is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

St 70-2 is a structural steel for wear and strength loaded parts (bolts, shafts, spindles, rails).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0

St 60-2 is a structural steel for wear and strength loaded parts (bolts, shafts, spindles, keys).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °

St 50-2 is a structural steel for wear and strength loaded parts (bolts, shafts, spindles, keys).PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °

St 37-2 is used for moderate loaded parts, without inspection.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °C184 GPa500.0 °C175 GPa600.0 °C164

The balanced high performance machining steel 9 SMnPb 36 shows an excellent cutting behaviour. Because of the S content a lower toughness and a increased crack danger. Application: mass components in the automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureV

The balanced machining steel 9 SMnPb 28 is used for higher demands on the cutting capacity and surface condition. The steel shows a lower crack sensitivity. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³Mechan

The balanced machining steel 9 SMn 36 is used for higher demands on the cutting capacity and surface condition. The steel shows a elevated crack sensitivity. Application: limited in the automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C

Balanced machining steel 9 SMn 28 is the standard grade for all mass turning tools and should be the substitution of the 9 S 20. The steel is suited for thin walled parts and little cold forming. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTempera

The fully killed machining steel 15 S 10 is applicated in the case hardened condition for thin walled parts with higher toughness demands. Application: automotive engineering, toolbuilding, apparatus engineeringPropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemper

The fully killed machining steel 10 SPb 20 shows a better machinability because of the Pb and S additions. Application in the case hardened condition for thin-walled parts in the automotive engineering, toolbuilding, apparatus engineering.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g

The fully killed machining steel 10 S 20 shows a better machinability with relative well toughness than the 15 S 10 and the 10 S 20. Application in the case hardened condition for thin-walled parts in the automotive engineering, toolbuilding, apparatus engineering.PropertiesGeneralPropertyTemperatur

Hot finished weldable structural hollow sections with circular, square, rectangular or elliptical cross-section for the steel and plant construction, civil engineering and vehicle construction.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMe

The structural steel (non-alloy high-grade steel) S220GD is deliverable with following hot-dip coatings: S220GD+Z (coating Zn), S220GD+ZF (coating Zn-Fe), S220GD+ZA (coating Zn-Al), S220GD+AZ (coating Al-Zn). The coating mass for Z amounts to 100, 140, 200, (225), 275, 350*, (450)* and (600)* g/m²,

The alloyed high-grade steel DX56D (special deep drawing quality) is deliverable with following hot-dip coatings: DX56D+Z (coating Zn), DX56D+ZF (coating Zn-Fe), DX56D+ZA (coating Zn-Al), DX56D+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), (275) g/m², for ZF to 100, 12

C75S is a high-carbon steel with high hardness and strength properties.PropertiesGeneralPropertyTemperatureValueDensity23.0 °C7.86 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus23.0 °C200 - 215 GPaTypical for High Carbon SteelHardness, Rockwell C23.0 °C38.5 - 54 [-]Hardness, Vickers23

The steel C125S is used as cold rolled strip for springs and special applications in thicknesses of up to 6 mm and as tempered cold strip in thicknesses from 0.30 to 3.00 mm. The springs made of steel C125S are suitable for highly stressed tension springs, especially in the watch industry, as well a

The hot rolled, unalloyed quality steel S450J0 will only be used for long products. The steel is not intended for heat treatment. Stress relieving annealing is allowed. Products in the delivery condition +N may be hot formed and/or normalized after delivery. The delivery condition is up to the produ

Rectangular and square welded precision tubes made from M 22 are manufactured by cold forming and electrical resistance welding. Application: automotive engineeringPropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureVa