The cold-upsettable steel 28 B 2 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for Phillips screws of strength class 8.8 in the thick and medium dimension range and for nuts of strength classes 8 an

The cold-upsettable steel 28 B 2 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for Phillips screws of strength class 8.8 in the thick and medium dimension range and for nuts of strength classes 8 an

The cold-upsettable steel 22 B 2 can be cold-formed with a medium to high rate of forming according to the usual forming methods. It is used for screws, bolts and pressed parts of strength class 8.8 in the thick and medium dimension range.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.82 g

The cold-upsettable steel 22 B 2 can be cold-formed with a medium to high rate of forming according to the usual forming methods. It is used for screws, bolts and pressed parts of strength class 8.8 in the thick and medium dimension range.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.82 g

The cold-upsettable steel 19 MnB 4 can be cold-formed in rolling-hard condition with a low to medium forming rate and in the heat-treated conditions GKZ and K+GKZ+K with a high forming degree. It is used in the un-annealed condition for hexagon screws and hexagon socket head cap screws of the streng

The cold-upsettable steel 19 MnB 4 can be cold-formed in rolling-hard condition with a low to medium forming rate and in the heat-treated conditions GKZ and K+GKZ+K with a high forming degree. It is used in the un-annealed condition for hexagon screws and hexagon socket head cap screws of the streng

The cold-upsettable steel Cq 15 is suitable for the manufacture of screws, nuts and small parts (valve spring plates, bearing sleeves) used in automobile, motor and equipment construction and in general engineering. For lower requirements and smaller sections, carbon steel is sufficient if the requ

The cold-upsettable steel Cq 15 is suitable for the manufacture of screws, nuts and small parts (valve spring plates, bearing sleeves) used in automobile, motor and equipment construction and in general engineering. For lower requirements and smaller sections, carbon steel is sufficient if the requ

The steel QSt 38-3 can undergo cold extrusion pressing and is suitable for the manufacture of mass-produced parts in general engineering, motor and automobile construction with high demands on the strength, surface condition and exactness of dimensions. Because of its smooth surface and high interna

The steel QSt 36-3 can undergo cold extrusion pressing and is suitable for the manufacture of mass-produced parts in general engineering, motor and automobile construction with high demands on the strength, surface condition and exactness of dimensions. Because of its smooth surface and high interna

The steel QSt 34-3 can undergo cold extrusion pressing and is suitable for the manufacture of mass-produced parts in general engineering, motor and automobile construction with high demands on the strength, surface condition and exactness of dimensions. Because of its smooth surface and high interna

The steel QSt 32-3 can undergo cold extrusion pressing and is suitable for the manufacture of mass-produced parts in general engineering, motor and automobile construction with high demands on the strength, surface condition and exactness of dimensions. Because of its smooth surface and high interna

Aluminum ASTM 3003 is a popular alloy that offers customers very good atmospheric corrosion resistance and moderate strength. Aluminum 3003 offers good machinability for aluminum alloys, though it is not heat treatable. Unlike other aluminum alloys, ASTM 3003 is weldable by conventional welding meth

Seamless precision steel tube made from St 45 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 35 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 35 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 35 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 30 Si is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi

ZSt 37-2 as bright drawn grade is used for moderate loaded parts, without inspection.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.85 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus-100.0 °C217 GPa20.0 °C212 GPa100.0 °C207 GPa200.0 °C199 GPa300.0 °C192 GPa400.0 °C184 GPa500.

Seamless precision steel tube made from St 30 Si is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load wi