Welded precision steel tubes made from RSt 34-2 are used for thin-walled precision constructional elements with a good surface condition.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23

Welded precision steel tubes made from RSt 34-2 are used for thin-walled precision constructional elements with a good surface condition.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23

Welded precision steel tubes made from RSt 34-2 are used for thin-walled precision constructional elements with a good surface condition.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23

Welded precision steel tubes made from RSt 34-2 are used for thin-walled precision constructional elements with a good surface condition.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23

Welded precision steel tubes made from RSt 34-2 are used for thin-walled precision constructional elements with a good surface condition.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon SteelMechanicalPropertyTemperatureValueCommentElastic modulus23

Seamless precision steel tube made from St 52 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 52 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 52 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 45 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Seamless precision steel tube made from St 45 is mainly used as construction element with special requirements in dimension accuracy, small wall thicknesses and good surface condition. The tubes are made in different grades (A and C). Grade C is valid for conduits. Grade A: for mechanical load witho

Free-cutting steel 11SMn37 is not intended for heat-treatment and is preferred 11SMn30 for higher machinability and surface appearance demands due to its higher S-content. The Pb-alloyed steel 11SMnPb30 is replaced by 11SMn37 for lower machinability requirements. Increased crack sensitivity has to b

Free-cutting steel 11SMn30 is not intended for heat-treatment and represents the standard grade for all bulk turned parts, also for parts of complicate machining of the complete cross-section (e.g. sparking plugs) and replaces a.o. steel 9SMn28 (DIN 1651 : 1988-04). Steel 11SMn30 is suitable for thi

Free-cutting steel 10S20, suitable for case-hardening, shows considerably uniformer properties of the cross-section and within the melt than older semi-killed free cutting steels. Compared to 15 S 10 (DIN 1651: 1988-04) shows 10S20 a slightly enhanced machinability at relatively favorable ductility

The standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping, and other utilities. It is primarily applicable to the North Sea Sector, but may als

Steel C45E is applicable for medium loaded parts of higher dimensions (large forged parts) and more complex form in vehicle manufacturing and machine engineering (e.g. shipshafts, transmission parts, wheel hubs).PropertiesGeneralPropertyTemperatureValueConditionRelated StandardsShapeDensity20 °C7.8

Steel P285QH is a tempered weldable fine grained steel with a yield strength of max. 285 N/mm². Application: pressure vessel construction, apparatus engineering, general machine and toolbuilding.PropertiesGeneralPropertyTemperatureValueCommentDensity23.0 °C7.8 - 7.9 g/cm³Typical for Low Carbon Stee

The structural steel (non-alloy high-grade steel) S350GD is deliverable with following hot-dip coatings: S350GD+Z (coating Zn), S350GD+ZF (coating Zn-Fe), S350GD+ZA (coating Zn-Al), S350GD+AZ (coating Al-Zn), S350GD+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275, 35

The structural steel (non-alloy high-grade steel) S320GD is deliverable with following hot-dip coatings: S320GD+Z (coating Zn), S320GD+ZF (coating Zn-Fe), S320GD+ZA (coating Zn-Al), S320GD+AZ (coating Al-Zn), S320GD+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275, 35

The structural steel (non-alloy high-grade steel) S280GD is deliverable with following hot-dip coatings: S280GD+Z (coating Zn), S280GD+ZF (coating Zn-Fe), S280GD+ZA (coating Zn-Al), S280GD+AZ (coating Al-Zn), S280GD+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275, 35

The structural steel (non-alloy high-grade steel) S250GD is deliverable with following hot-dip coatings: S250GD+Z (coating Zn), S250GD+ZF (coating Zn-Fe), S250GD+ZA (coating Zn-Al), S250GD+AZ (coating Al-Zn), S250GD+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275, 35