The cold-upsettable steel 17 Cr 3 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gear

G-X 30 CrNiSiNb 24 24, for industry oven and natural gas systems resistance: - in carburising gas: good - in nitrogenous gas: good - in oxidising sulfureous gas: middle - in reductive sulfureous gas: low - temperature loading on air: up to 1050°CPropertiesGeneralPropertyTemperatureValueDensity20.0 °

The fully killed machining steel 60 SPb 20 is used for mass parts of highest strength, especially for lower toughness demands cross-sectional. Its better machinable because of the Pb addition. Application in the automotive engineering, toolbuilding, apparatus engineering (screws, nuts, smal parts).P

The fully killed machining steel 45 SPb 20 is used for mass parts of higher strength, especially for lower toughness demands cross-sectional. Its better machinable because of the Pb addition. Application in the automotive engineering, toolbuilding, apparatus engineering (screws, nuts, smal parts).Pr

The fully killed machining steel 35 SPb 20 is used for mass parts of mean strength, especially for lower toughness demands cross-sectional. Its better machinable because of the Pb addition. Application in the automotive engineering, toolbuilding, apparatus engineering (screws, nuts, smal parts).Prop

GS-X 22 CrMoV 12 1 is usabel upt to 600 °C verwendbar. For valve cases, steam collector cases and turbine housings.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.7 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C216 GPa100.0 °C209 GPa200.0 °C200 GPa300.0 °C190 GPa400.0

The nitriding steel 31 CrMo 12 can undergo quenchhardening and is used for heavy machine parts that are subjected to wear, have a high surface hardness and have a dimension of up to 250 mm. With parts for hot steam fittings such as valve spindles, it is used for dimensions of up to 100 mm and under

The nitriding steel 15 CrMoV 5 9 can undergo quenchhardening and is used for machine parts that are subjected to wear and have a dimension of up to 250 mm. The steel contains a nitride agent (Cr) which contributes through the nitriding process or the nitro-carburization process with N or N and C to

X 3 CrNiCu 18 9 is an austenitic stainless steel with a low carbon content for special application (possible use for screws, nuts and molded parts) also in low temperatures. The steel is resistant to intercrystalline corrosion and can be cold-formed well.PropertiesGeneralPropertyTemperatureValueDens

The cold-upsettable steel Cq 45 can be cold-formed with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. BEcause of its unfavourable processing properties, Cq 45 should be replaced with steel 35 B 2. It is used for normed screws of stren

The cold-upsettable steel Cq 35 can be cold-formed with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used, for example, for screws in the lower dimension range as well as for nuts of strength class 8.8.PropertiesGeneralPropertyTempera

Because of its high carbon content, the cold-upsettable steel 46 Cr 2 can be processed in cold condition only with a small to medium rate of forming. It is used for screws and bolts of strength class 8.8 in the lower dimension range. The steel 46 Cr 2 will be replaced with steel 35 B 2.PropertiesGen

Because of its high carbon content, the cold-upsettable steel 46 Cr 2 can be processed in cold condition only with a small to medium rate of forming. It is used for screws and bolts of strength class 8.8 in the lower dimension range. The steel 46 Cr 2 will be replaced with steel 35 B 2.PropertiesGen

Because of its high carbon content, the cold-upsettable steel 46 Cr 2 can be processed in cold condition only with a small to medium rate of forming. It is used for screws and bolts of strength class 8.8 in the lower dimension range. The steel 46 Cr 2 will be replaced with steel 35 B 2.PropertiesGen

The cold-upsettable steel 42 CrMo 4 can be cold-formed according to the usual forming methods on single-stage and multi-stage presses. Because of its high carbon content, only low to medium forming degrees are recommendable. It is used for screws of strength class 10.9 in the thick and of strength c

The cold-upsettable steel 42 CrMo 4 can be cold-formed according to the usual forming methods on single-stage and multi-stage presses. Because of its high carbon content, only low to medium forming degrees are recommendable. It is used for screws of strength class 10.9 in the thick and of strength c

The cold-upsettable steel 42 CrMo 4 can be cold-formed according to the usual forming methods on single-stage and multi-stage presses. Because of its high carbon content, only low to medium forming degrees are recommendable. It is used for screws of strength class 10.9 in the thick and of strength c

The cold-upsettable steel 41 Cr 4 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for normed screws and screws manufactured according to drawings of strength class 8.8 in the th

The cold-upsettable steel 41 Cr 4 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for normed screws and screws manufactured according to drawings of strength class 8.8 in the th

The cold-upsettable steel 41 Cr 4 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for normed screws and screws manufactured according to drawings of strength class 8.8 in the th