Steel 38 Cr 2 is suitable for a little higher strained parts of lower dimension in vehicle manufacturing, engine and machine engineering (e.g. transmission parts, axles, shafts). Lowest application temp. -25 °C.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 g/cm³MechanicalPropertyTempera

The cold-upsettable steel 38 Cr 2 can be cold-formed with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for screws of strength class 8.8 in the lower dimension range. The steel 38 Cr 2will be replaced with steel 35 B 2.PropertiesG

The cold-upsettable steel 38 Cr 2 can be cold-formed with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for screws of strength class 8.8 in the lower dimension range. The steel 38 Cr 2will be replaced with steel 35 B 2.PropertiesG

The cold-upsettable steel 37 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for screws of strength class 8.8 in the thick dimension range.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7

The cold-upsettable steel 37 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for screws of strength class 8.8 in the thick dimension range.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7

The cold-upsettable steel 37 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for screws of strength class 8.8 in the thick dimension range.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7

The cold-upsettable steel 34 CrNiMo 6 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength classes 10.9 and 12.9 in the thick dimension range and

The cold-upsettable steel 34 CrNiMo 6 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength classes 10.9 and 12.9 in the thick dimension range and

The cold-upsettable steel 34 CrNiMo 6 can be cold-formed with the suitable tools with a low to medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength classes 10.9 and 12.9 in the thick dimension range and

The cold-upsettable steel 34 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for hexagon screws and hexagon socket head cap screw of strength class 8.8 in the medium to thick dimension range and

The cold-upsettable steel 34 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for hexagon screws and hexagon socket head cap screw of strength class 8.8 in the medium to thick dimension range and

The cold-upsettable steel 34 Cr 4 can be cold-formed with a medium to high rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for hexagon screws and hexagon socket head cap screw of strength class 8.8 in the medium to thick dimension range and

The cold-upsettable steel 34 CrNiMo 8 can be cold-formed with the suitable tools with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength class 12.9 in the thick dimension range. For special stress,

The cold-upsettable steel 34 CrNiMo 8 can be cold-formed with the suitable tools with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength class 12.9 in the thick dimension range. For special stress,

The cold-upsettable steel 34 CrNiMo 8 can be cold-formed with the suitable tools with a medium rate of forming according to the usual forming methods on single-stage and multi-stage presses. It is used for high-strength screws of strength class 12.9 in the thick dimension range. For special stress,

The cold-upsettable steel 20 MoCr 5 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gea

The cold-upsettable steel 20 MoCr 5 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gea

The cold-upsettable steel 20 MoCr 5 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gea

The cold-upsettable steel 17 Cr 3 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gear

The cold-upsettable steel 17 Cr 3 is suitable for the manufacture of screws and nuts (soft-annealed condition with pre- and/or post treatment) used in automobile, motor and equipment construction and in general engineering. The steel finds additional use, amongst other things, for bevel gears, gear