CW602N is suited for cold forming, easy to machine and resistant to dezincification.Application: water supplyPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.4 - 8.46 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0 °C105 GPaElongation20.0 °C25 %Hardness, Brinell20.0 °C70 -

Material CuNi7Zn39Pb3Mn2, mat. No. CW400J, is incomparable to a DIN-mark. It is used in the form of bars, prematerial for forged parts, forged parts, wires and profiles.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.44 - 8.5 g/cm³MechanicalPropertyTemperatureValueCommentElastic modulus20.0

Propertties: - good corrosion resistance to water and steam - is able for high gloss polishing - application temperature: -40 up to 550°C Application: - for construction elements, requiring higher strengths because higher mechanical loadings - axis, parts for pumps, plunger, valve cone, nozzle pin,

The material X14CrMoS17 is used acc. DIN 17440 : 1996-09 for rods (for pressure vessels), forgings and drawn wire. For the application acc. DIN 17440 : 1985-07 (X 12 CrMoS 17) resp. acc. DIN EN 10088-1,-2,-3 : 1995-08 (X14CrMoS17) applies: stainless free-cutting steel used in the quenched and temper

The austenitic steel grade X2CrNiMoN25-7-4 is applicated in solution annealed condition in the form of cold rolled strip, warm rolled strip and warm rolled sheet as well as for rods, wire rods and profiles. The material is resistant to intercrystalline corrosion also in sensitized condition.Properti

The austenitic-ferritic steel grade X2CrNiMo23-5-3 acc. to DIN EN 10272 : 2001-01 is used for hot and cold formed rods for pressure vessels. The material shows high resistance to stress corrosion in chlorid containing medis as well as favorable resistance to pitting and intercrystalline corrosion al

The austenitic-ferritic material X2CrNiMoCuWN25-7-4 is applicated in solution annealed condition in the form of warm rolled sheet, rods, wire rods and profiles. The material is resistant to intercrystalline corrosion also in sensitized condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °

The austenitic steel grade X2CrNiMoCuN25-6-3 acc. to DIN EN 10272 : 2001-01is used for hot and cold formed rods for pressure vessels. The material is resistant to intercrystalline corrosion also in sensitized condition.PropertiesGeneralPropertyTemperatureValueDensity20.0 °C7.8 g/cm³MechanicalPropert

The ferritic steel grade X2CrNi12 acc. to DIN EN 10272 : 2001-01is used for hot and cold formed rods for pressure vessel. The material shows a considerably better corrosion resistance than general construction steels, but it is more cost-efficient than high-alloyed stainless steels. Its corrosion re

CuTeP, mat. No CW118C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuTeP, mat. No 2.1546, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. CuTeP is applicated as free-cutting alloy due to its favorable machinability. Th

CuSP, mat. No CW114C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuSP, mat. No 2.1498, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. Already low S-contents increase the temperature for removal of workhardening to ap

Quenched and tempered steel for fasteners with specified elevated and/or low temperature properties,Low-temperature Ni-alloyed steel for pressure vessel construction, for refrigerators, gearbox parts and components in machine and apparatus engineering which are exposed temperatures up to -200 °C Fur

Hardenable austenitic high-temperature steel with boron addition for an increase of thermal resistance and creep behavior as well as for neutron absorption. Thermal resistance up to 650 °C, scaling resistance up to 750 °C Application for screws and nuts, steam and gas turbines and in chemical indus

Unstabilized austenitic high-temperature steel with good thermal resistance up to 700 °C for application in power station engineering (sodium-cooled fast breeder, pressure vessels, fittings, pipelines), in chemical industry as well as for superheater tubes and turbine lines. Further application for

The unstabilized austenitic steel X6CrNi18-10 (1.4948) shows good thermal resistance up to 650 °C Application in reactor engineering (sodium cooling circuit at fast breeders) as well as in steam boiler construction and in chemical industry. Further application for mounting elements at increased temp

Trademark X5CrNiMo17-12-2 is comparable to X 5 CrNiMo 17 12 2 acc. to DIN17440-85. This material is an austenitic CrNiMo-steel with increased resistance to non-oxidizing acids and halogenated media, to intercrystalline corrosion in delivery condition. It is suitable for mirror finishing and well col

Trademark X5CrNiMo17-12-2 is comparable to X 5 CrNiMo 17 12 2 acc. to DIN17440-85. This material is an austenitic CrNiMo-steel with increased resistance to non-oxidizing acids and halogenated media, to intercrystalline corrosion in delivery condition. It is suitable for mirror finishing and well col

X5CrNi18-10 as a standard type of the austenitic CrNi-steels is comparable to X 5 CrNi 18 10 acc. to DIN 17440-85. It shows high corrosion resistance but no resistance to intercrystalline corrosion in sensitized condition as well as good processability. The steel is suitable for mirror finishing and

X5CrNi18-10 as a standard type of the austenitic CrNi-steels is comparable to X 5 CrNi 18 10 acc. to DIN 17440-85. It shows high corrosion resistance but no resistance to intercrystalline corrosion in sensitized condition as well as good processability. The steel is suitable for mirror finishing and

Application: general purpose wire, springs, fastenersPropertiesGeneralPropertyTemperatureValueDensity20.0 °C8.8 - 8.9 g/cm³MechanicalPropertyTemperatureValueElastic modulus20.0 °C138 GPaElongation20.0 °C10 %Elongation A10020.0 °C3 - 6 %Elongation A11.320.0 °C6 - 8 %Tensile strength20.0 °C680 MPaYiel